Aquaphalt 6.0 (Medium)

Aquaphalt™ is a revolutionary, high performance, flexible, reactive, cold-mix, asphalt repair product for use in repairing asphalt and concrete road surfaces. Aquaphalt™ reacts with plain water to provide a permanent repair solution. All sizes of Aquaphalt™ are free of solvents or volatile organic compounds (VOCs). This product is offered in a 23 KG pail.

Product Code: 13503023, 23503023

• Stronger than typical hot-mix asphalt pavements
• Saves time and money by eliminating costly repeat repairs
• Contains no toxic solvents or VOCs, making it friendlier to the environment


1. FEATURES & BENEFITS

Permanent Solution: Aquaphalt™ is stronger than typical hot-mix asphalt pavements
Cost Effective: Aquaphalt™ saves time and money by eliminating costly repeat repairs
Environmentally Sustainable: Aquaphalt™ contains no toxic solvents or VOCs, making it friendlier to the environment

2. USES

This product can be used on highways (asphalt or concrete), runways/taxiways/aprons, bridge decks, manhole repairs, potholes, utility cuts, parking lots, driveways, tennis courts, and pathways.

3. PROCEDURES

Remove all loose material from area to be repaired. Place Aquaphalt™ in the patch and level with a rake or trowel. Allow 0.5” (1.3 cm) to 1.0” (2.5 cm) of additional height for compaction. Saturate with water and compact. If the depth of the pothole is greater than 2.0” (5.1 cm) to 3.0” (7.6 cm), it is advisable to fill the hole in two layers.

4. TECHNICAL DATA

Aggregates: All of the aggregate materials are a crushed granite and are from an approved Virginia DOT source. All of the aggregate materials are from a non‐polishing source and have the following properties: ASTM C-127, 128; Specific Gravity: 3.0% Max.

Binder: Reactive Binder is a further development of the “Raps‐Asphalt” technology. “Raps‐Asphalt” is a plant-based binder with bitumen (a naturally occurring Organic by-product of organic materials), which represents a total weight of approximately 5‐8% of the finished product. This binder contains natural rapeseed oil which improves stability. The binder of Aquaphalt™ is a proprietary liquid that similarly contains renewable natural raw materials.

Gradation Analysis

Sieve Sizes 6.0 mm % Passing
1/2″ Sieve 100
3/8″ Sieve 100
#4 85-100
#8 20-55
#16 12-32
#200 3-6

 

5. CURING

Aquaphalt™ hardens quickly for immediate use. After water is applied, Aquaphalt™ will start to cure in 15 minutes and can be opened to traffic immediately. The reactive process happens relatively quickly and Aquaphalt starts to get hard and in most cases will be fully cured in 24 hours. Since Aquaphalt™ does not release any harmful VOCs, it can be sealed 24 hours after installation.

6. YIELD

Coverage Rate:
1 m2 per 23 KG pail at 1 cm depth, of 5 ft2 per 50 lb pail at 1″ depth

Recommended Installation Depth:
2.5 cm (1″) to 3.2 cm (1 1/4″)

7. CLEAN-UP

Use automotive hand cleaners on hands. Tools may be cleaned with light oil, mineral spirits, or vegetable oil.

8. STORAGE & HANDLING

Each bucket of Aquaphalt™ contains approximately 23 KG (50 lb) of material. Store indoors, in cool, dry conditions. Avoid direct sunlight and/or exposure to freezing. Aquaphalt™ can be applied in freezing conditions, but workability is best when it is stored indoors.

Warranty

RoadStone Production LLC, a Virginia limited liability company (RSP), provides an unlimited “CURING GUARANTEE” to the Customer that Aquaphalt™ product[s], produced by RSP LLC, and sold by its authorized Distributors will cure, upon proper installation – as directed in written form by the manufacturer and applicable standards – within a reasonable time frame (24 hours to 120 hours) from the date of installation. See website for more details: www.aquaphalt.com.

Aquaphalt™ is a revolutionary, high performance, flexible, reactive, cold-mix, asphalt repair product for use in repairing asphalt and concrete road surfaces. Aquaphalt™ reacts with plain water to provide a permanent repair solution. All sizes of Aquaphalt™ are free of solvents or volatile organic compounds (VOCs). This product is offered in a 23 KG pail.

Product Code: 13503023, 23503023

• Stronger than typical hot-mix asphalt pavements
• Saves time and money by eliminating costly repeat repairs
• Contains no toxic solvents or VOCs, making it friendlier to the environment


SECTION 1: IDENTIFICATION

Product Identifier

Cold Asphalt Mix

Other Means of Identification Aquaphalt Premium 4.0, 6.0, 9.0, 12.0
Recommended Use

Reactively curing, cold applies asphalt mix, free of solvents.

Manufacturer/Supplier Identifier

RoadStone Production LLC, 1230 River Road, Charlottesville, VA 22901, USA

Emergency Phone No.

24 hours: Chemtrec, 1-800-424-9300, Information Contact: 866-784-5031 (Monday-Friday, 8:00 a.m. – 3:00 p.m. EST)

Date of Preparation

January 2015

SECTION 2: HAZARD IDENTIFICATION

Signal Word:
Warning

Hazard Statement(s):
The product is classified as not acute toxic, not sub-acute respectively chronically toxic, and classified as not irritating or sensitizing. Causes mild/moderate eye irritation (tears, blurred vision and redness), prolonged exposure may cause moderate skin irritation. May cause drying/defatting of the skin. Not likely to be toxic if ingested, but may cause irritation of the mouth, throat and stomach. See Section 11 for more information.

This product does not contain any carcinogens or potential carcinogens as listed by OSHA, IARC or NTP. While this material is not considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200), this MSDS contains valuable information critical to the safe handling and proper use of the product. This MSDS should be retained and available for employees and other users of this product.

Potential Environmental Effects: See Section 12 for more information

SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS

Component CAS # % by Wt. Other Identifiers
Mineral aggregates Various 92 – 94%
OMV Bitumen 106/220 8052-42-4 6-8%

 

HAZARDS DISCLOSURE: This product contains no known hazardous materials as defined by the OSHA Hazard Communication Standard 29 CFR 1910.1200.

SECTION 4: FIRST-AID MEASURES

First-Aid Measures

Eye contact
Rinse opened eye for several minutes under running water; consult a physician.
Skin contact
Remove contaminated clothing and wash before reuse. Wash skin with soap and
water. Get medical attention if irritation develops.
Inhalation
Not relevant.
Ingestion
Do NOT induce vomiting. Do NOT administer anything by mouth to unconscious
person. Offer water to drink. Get medical attention.

Note to Physicians: Not relevant.

SECTION 5: FIRE-FIGHTING MEASURES

Suitable Extinguishing Media
Foam, powder, water spray
Unsuitable Extinguishing Media
Water stream
Products of Combustion
Not applicable
Specific firefighting methods
No specific methods required
Specific protective devices
Self-contained breathing apparatus
Specific hazards
No specific hazards known
Protection of Firefighters
Firefighters should wear self-contained breathing apparatus and full fire-fighting turnout gear.

SECTION 6: ACCIDENTAL RELEASE MEASURES

Personal precautionary measures
No special measures required.
Environmental precautionary measures
Observe usual precautions.
Methods for cleaning up
Collect mechanically.
Other Information
Spills of this material do not need to be reported to the National Response Center.

SECTION 7: HANDLING AND STORAGE

Handling
Keep away from heat, sparks and flame – do not smoke – Do not get in eyes. Do not breathe vapor. Avoid prolonged contact with skin.

Storage

Requirements on storage rooms and containers
Store in weather / sun protected area! Keep container well closed, material cures by exposure to air. Product residue may remain in empty containers. Observe all label precautions until container is cleaned, reconditioned or destroyed.
Information about storage in a common storage facility
Not relevant
Further information about storage conditions
Store in weather / sun protected area
Storage class according to VCI
Not relevant.
Appropriate application(s)
For patching up asphalt and concrete

SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION

Exposure Guidelines
Component 1: Not established.
Component 2: Not established.

Engineering Measures
No special requirement.

Components with critical values that require inspection at the place of work: The product does not contain any relevant quantities of material with critical values, which have to be monitored at a work place.

Eye/Face Protection
Not required
Skin Protection
Wear suitable work gloves.
Respiratory Protection
Not required

General Hygiene Considerations
Wash thoroughly after handling. Have eye-wash facilities immediately available. Do not eat, drink and smoke while working.

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

Basic Physical and Chemical Properties

Appearance Black, solid
Odour Characteristic
Odour Threshold Not available
Physical state Mineral – binder – mix
pH – value Not relevant
Freezing point Not relevant
Boiling point Not relevant
Flash point Not relevant
Flammability Not relevant
Upper Flammability Limit Not relevant
Lower Flammability Limit Not relevant
Vapour pressure at 20° C/68 °F [mmHg] Not relevant
Vapor Density at 25° C/68 °F 2.0-2.5
Solubility in Water at 20° C/68 °F Not relevant
Solubility in Fat at 20° C/68 °F Not relevant
Auto-ignition Temperature Not available
Dynamic viscosity at 20° C/68 °F [mPas] Not relevant
Percent Volatile, wt. % _0_
Volatile Organic Compound (VOC) Content, wt. % _0_
Fire Promoting Properties [°C] Product is not oxidizing
Danger of explosion [°C] Product is not explosive

SECTION 10: STABILITY AND REACTIVITY

Stability
Stable.
Conditions to avoid
Keep away from heat, sparks and flames.
Incompatible Materials
not relevant
Possibility of Hazardous Reactions
Will not occur.
Hazardous Decomposition Products
Not relevant

SECTION 11: TOXICOLOGICAL INFORMATION

No adverse effects are expected if this product is handled in accordance with this Safety Data Sheet and the product label. Symptoms or effects that arise when the product is mishandled or overexposure occurs are:

ACUTE EFFECTS
The product is classified as not acute toxic.
CHRONIC EFFECTS*
The product is classified as not sub-acute respectively chronically toxic.

Corrosive or Irritant Effect or Sensitization
The product is classified as not irritating or sensitizing.

Likely Routes of Exposure
Eye contact, skin contact.

Eye
Causes mild/moderate irritation (tears, blurred vision and redness).
Skin
Prolonged exposure may cause moderate skin irritation. May cause drying/defatting of the skin.
Ingestion
Not likely to be toxic but may cause irritation of the mouth, throat and stomach.
Inhalation
Not relevant
Medical Conditions Aggravated By Exposure
May cause more significant skin irritation in people with pre-existing skin conditions.

SECTION 12: ECOLOGICAL INFORMATION

Mobility in Environment
Not relevant.
Persistence/ Degradability
Not relevant.
Bioaccumulation/ Accumulation
Not relevant.
Further negative effects
There are no negative effects known.

SECTION 13: DISPOSAL CONSIDERATIONS

Disposal
Dispose of in accordance with federal, state and local regulations.*
Packaging
Packaging can be reused or recycled after cleaning. Note local restrictions.*

SECTION 14: TRANSPORT INFORMATION

UN Number
Not applicable
UN Proper Shipping Name
Not applicable
Transport Hazard Class(es)
Not applicable
Packing Group (if applicable)
Not applicable
Marine Pollutant (Y/N)
Not available
Special Precautions
Not available

US DOT (ground)
Proper Shipping Description: This product is not regulated for shipping by US DOT.
Canadian TDG (ground)
Proper Shipping Description: See US DOT
ICAO (air)
Proper Shipping Description: See US DOT
IMDG (water)
Proper Shipping Description: See US DOT
ADR/ RID
Proper Shipping Description: See US DOT
ADN/ ADNR
Proper Shipping Description: See US DOT

SECTION 15: REGULATORY INFORMATION

OSHA PROCESS SAFETY (29CFR1910.119)
Not regulated.
Inventory Status
United States (TSCA): All ingredients are on the inventory or exempt from listing.

SECTION 16: OTHER INFORMATION

NFPA 704: National Fire Protection Association
Health – 0, Fire – 0, Reactivity –1
0 = minimal hazard, 1 = slight hazard, 2 = moderate hazard, 3 = severe hazard, 4 = extreme hazard

The above SDS complies with OSHA hazard communication standard 29 CFR 1910.1200(g), as revised in 2012.

Modifications compared to a prior version are marked with the star symbol * on the right margin.

Prepared by Roadstone Production LLC (revised by OHK Environmental Consulting, LLC, July 2015)

Disclaimer

Roadstone Production LCC: To the best of our belief, information and knowledge, we believe the information contained in this MSDS to be accurate and reliable as of the date of this Material Safety Data Sheet. The above information is based on information received from raw material suppliers and other sources and references the products as currently formulated. We make no expressed or implied warranty regarding the accuracy or reliability of the data or results obtained from the use of the product and assume no responsibility or liability for personal injury or property damage incurred by the use of these materials due to the fact that the conditions of handling, use, and storage of these materials are beyond our control. Any and all materials should be used with caution and may present unknown hazards. The information and recommendations in this material safety data sheet are offered for the users’ consideration and examination. It is each user’s responsibility to determine if the information and data contained herein is suitable and to comply with all applicable international, federal, state, and local laws and regulations.


Product Calculator


How Much Do I Need?

Calculate how much of a product you need, then add it to your Shopping List.
Jump To Calculator Icon

Jump To Calculator


How-To Video

More Information

To clean-up, use automotive hand cleaners on hands. Tools may be cleaned with light oil, mineral spirits or vegetable oil. For a how-to guide, watch the video above.