Rapid Set® NewCrete

Rapid Set® NewCrete is a concrete resurfacer that is a fast, strong and durable hydraulic cement product. This easy to use product makes old concrete look new! The material has a 30 minute working time, and can be opened to foot traffic in 2 to 3 hours. Offered in 25 lb (11.3 KG) boxes.

• Easy to use; just add water
• Make old concrete look new
• Concrete gray colour
• Rapid strength gain
• 30 minute working time
• Foot traffic in 2 to 3 hours


1. DESCRIPTION

Rapid Set® NEWCRETE is a high performance polymer-modified mortar that can be used to resurface worn, old or spalled concrete, giving a new concrete look. The advanced hydraulic cement used in NEWCRETE provides a durable surface for both indoor and outdoor use. NEWCRETE has been specially formulated to match the color of typical portland cement concrete. Cutting-edge self-curing technology (SCT) means wet curing is not required in most applications. NEWCRETE has a working time of up to 30 minutes and can receive foot traffic in as soon as 2 to 3 hours.

2. USES

Use NEWCRETE to renew old, damaged or discolored concrete.

3. HIGHLIGHTS & ENVIRONMENTAL ADVANTAGES

Use NEWCRETE to reduce your carbon footprint and lower your environmental impact. Production of Rapid Set cement emits far less CO2 than portland cement. Contact your CTS representative for LEED values and environmental information.

Highlights:
• Make old concrete look new
• Easy to use
• Self-Curing Technology (SCT)
• Rapid strength gain
• Polymer modified
• Concrete gray color
• 30 minute working time
• Foot traffic in 2 to 3 hours
• Interior/exterior

4. PROCEDURES

APPLICATION: Typical application thicknesses range from skim coat to 1/8″ (0.32 cm). NEWCRETE may be used to prefill cracks, spalls and holes up to 1/2″ (1.2 cm) thick prior to resurfacing. For larger repairs, use Rapid Set concrete repair products.

SURFACE PREPARATION: Application surface must be clean, sound and free from any materials that may inhibit bond, such as oil, asphalt, curing compound, acid, dirt and loose debris. Roughen surface and remove all unsound material. Apply NEWCRETE to a surface that is thoroughly saturated with no standing water. Surface must have a minimum temperature of 50˚F (10˚C).

PRIMING: Priming is not required. For porous substrates, use Rapid Set® Acrylic Primer to minimize the formation of pinholes on the surface. Follow all product application instructions.

MIXING: Organize work so that personnel and equipment are in place before mixing. Use clean potable water. NEWCRETE may be mixed using 2.5 to 3 quarts (2.3 L to 2.8 L) of water per 25-lb (11.3-kg) box. Use less water to achieve higher strengths. Do not exceed 3 quarts (2.8 L) of water per box. Place the desired quantity of mix water into the mixing container. Add material while mixing. Mix for the minimum amount of time required to achieve a lump-free, uniform consistency (usually 2 to 3 minutes). Do not retemper. Mixed NEWCRETE should be used within 30 minutes at 70˚F (21˚C).

PLACEMENT: Place quickly to allow for maximum finishing time. Once applied, typical finishing time is 5 to 10 minutes. Thinner applications will set faster. Do not wait for bleed water; apply final finish as soon as possible. NEWCRETE may be troweled, floated or broom finished. Do not install on frozen surfaces.

5. CURING

Rapid Set® NEWCRETE does not require water curing or curing compound under moderate conditions at 70˚F (21˚C). In dry, windy or hot conditions, mist with water to maintain a continuously wet surface until the product has achieved sufficient strength. NEWCRETE cures to a light gray color. Walk on time is approximately 2 to 3 hours.

COLD WEATHER: Environmental and material temperatures below 70˚F (21˚C) may delay setting time and reduce the rate of strength gain. Lower temperatures will have a more pronounced effect. Thinner sections will be more significantly affected. To compensate for cold temperatures, keep material warm, and use heated mix water.

WARM WEATHER: Environmental and material temperatures above 70˚F (21˚C) may shorten setting time and increase the rate of strength gain. Higher temperatures will have a more pronounced effect. To compensate for warm temperatures, keep material cool, use chilled mix water.

6. TYPICAL PHYSICAL DATA

Compressive Strength, ASTM C109 Mod.

24 hours 13.7 MPa (2000 psi)
28 days 31.0 MPa (4000 psi)

 

All data produced at 70˚F (21˚C) at 3 quarts of water

7. YIELD & PACKAGING

The coverage of one 25-lb (11.3-kg) box of NEWCRETE is approximately 75 ft2 (7.0 m2) at 1/16″ (0.16 cm) depth or 150 ft2 (13.9 m2) at skim coat depth. Coverage may vary due to jobsite conditions.

8. SHELF LIFE

NEWCRETE has a shelf life of 12 months when stored properly in a dry location, protected from moisture, out of direct sunlight, and in an undamaged package.

9. USER RESPONSIBILITY

Before using CTS products, read current technical data sheets, bulletins, product labels and safety data sheets at www.CTScement.com. It is the user’s responsibility to review instructions and warnings for any CTS products prior to use.

WARNING: DO NOT BREATHE DUST. AVOID CONTACT WITH SKIN AND EYES. Use material in well-ventilated areas only. Exposure to cement dust may irritate eyes, nose, throat, and the upper respiratory system/lungs. Silica exposure by inhalation may result in the development of lung injuries and pulmonary diseases, including silicosis and lung cancer. Seek medical treatment if you experience difficulty breathing while using this product. The use of a NIOSH/MSHA-approved respirator (P-, N- or R-95) is recommended to minimize inhalation of cement dust. Eat and drink only in dust-free areas to avoid ingesting cement dust. Skin contact with dry material or wet mixtures may result in bodily injury ranging from moderate irritation and thickening/cracking of skin to severe skin damage from chemical burns. If irritation or burning occurs, seek medical treatment. Protect eyes with goggles or safety glasses with side shields. Cover skin with protective clothing. Use chemical resistant gloves and waterproof boots. In case of skin contact with cement dust, immediately wash off dust with soap and water to avoid skin damage. In case of skin contact with wet concrete, wash exposed skin areas with cold running water as soon as possible. In case of eye contact with cement dust, flush immediately and repeatedly with clean water, and consult a physician. If wet concrete splashes into eyes, rinse eyes with clean water for at least 15 minutes and go to the hospital for further treatment.

Please refer to the SDS and www.CTScement.com for additional safety information regarding this material.

Limited Warranty

CTS CEMENT MANUFACTURING CORP. (CTS) warrants its materials to be of good quality and, at its option, will replace or refund the purchase price of any material proven to be defective within one (1) year from date of purchase. The above remedies shall be the limit of CTS’s responsibility. Except for the foregoing, all warranties expressed or implied, including merchantability and fitness for a particular purpose, are excluded. CTS shall not be liable for any consequential, incidental, or special damages arising directly or indirectly from the use of the materials.

Rapid Set® NewCrete is a concrete resurfacer that is a fast, strong and durable hydraulic cement product. This easy to use product makes old concrete look new! The material has a 30 minute working time, and can be opened to foot traffic in 2 to 3 hours. Offered in 25 lb (11.3 KG) boxes.

• Easy to use; just add water
• Make old concrete look new
• Concrete gray colour
• Rapid strength gain
• 30 minute working time
• Foot traffic in 2 to 3 hours


SECTION 1: Identification

Product identifier Rapid Set NewCrete
Other means of identification Product code 193010025, 193010050, 193012000
Recommended use Industrial use.
Recommended restrictions Workers (and your customers or users in the case of resale) should be informed of the potential presence of respirable dust and respirable crystalline silica as well as their potential hazards. Appropriate training in the proper use and handling of this material should be provided as required under applicable regulations.
Manufacturer/Importer/Supplier/Distributor information CTS Cement Manufacturing Corporation
12442 Knott Street Garden Grove, CA 92841
United States
1-800-929-3030
info@ctscement.com
Contact person – Safety Officer
Emergency telephone number 1-800-929-3030 (8 AM – 5 PM)

SECTION 2: Hazard(s) Identification

Physical hazards
Not classified.

Health Hazards
Skin corrosion/irritation – Category 2
Serious eye damage/eye irritation – Category 1
Carcinogenicity – Category 1A
Specific Target Organ Toxicity, Single Exposure – Category 3: respiratory tract irritation
Specific Target Organ Toxicity, Repeated Exposure – Category 2: lungs

OSHA defined hazards
Not classified.

Label elements

Signal word
Danger

Hazard statement
Causes skin irritation. Causes serious eye damage. May cause cancer. May cause respiratory irritation. May cause damage to organs (Lungs) through prolonged or repeated exposure.

Precautionary statement
Prevention
Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Do not breathe dust. Wash thoroughly after handling. Use in a well-ventilated area. Wear protective gloves/protective clothing/eye protection/face protection.
Response
If exposed or concerned: Get medical advice/attention. If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a poison center/doctor. If on skin: Wash with plenty of water. If skin irritation occurs: Get medical advice/attention. Take off contaminated clothing and wash before reuse. If inhaled: Remove person to fresh air and keep comfortable for breathing. Call a poison center/doctor if you feel unwell.
Storage
Store in dry location. Store away from incompatible materials.
Disposal
Dispose of contents/container in accordance with local/regional/national/international regulations.

Hazard(s) not otherwise classified (HNOC)
None known.

SECTION 3: Composition/information on ingredients

Mixtures

Chemical Name CAS number % Other Identifiers
Calcium Sulfoaluminate Cement 960375-09-1 25-70 Not applicable
Silica Sand 14808-60-7 30-50 Not applicable
Iron Oxide 1309-37-1 0-1 Not applicable
Methanal 50-00-0 0-0.05 Not applicable

 

Composition comments
All concentrations are in percent by weight unless ingredient is a gas. Gas concentrations are in percent by volume.

SECTION 4: First-aid measures

Inhalation
If dust from the material is inhaled, remove the affected person immediately to fresh air. Call a physician if symptoms develop or persist.

Skin contact
Remove contaminated clothing. Wash with plenty of soap and water. If skin irritation occurs: Get medical advice/attention. Wash contaminated clothing before reuse.

Eye contact
Do not rub eyes. Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Get medical attention immediately.

Ingestion
Immediately rinse mouth and drink plenty of water. Call an ambulance and take these instructions. Get medical attention if symptoms occur.

Most important symptoms/effects, acute and delayed
Severe eye irritation. Symptoms may include stinging, tearing, redness, swelling, and blurred vision. Permanent eye damage including blindness could result. Upper respiratory tract irritation. Coughing. Discomfort in the chest. Shortness of breath. Wheezing. Skin irritation.

Indication of immediate medical attention and special treatment needed
Provide general supportive measures and treat symptomatically. Keep victim under observation. Symptoms may be delayed.

General information
If you feel unwell, seek medical advice (show the label where possible). Ensure that medical personnel are aware of the material(s) involved, and take precautions to protect themselves. Show this safety data sheet to the doctor in attendance.

SECTION 5: Fire-fighting measures

Suitable extinguishing media
Water fog. Foam. Dry chemical powder.

Unsuitable extinguishing media
Do not use water jet as an extinguisher, as this will spread the fire.

Specific hazards arising from the chemical
During fire, gases hazardous to health may be formed.

Special protective equipment and precautions for firefighters
Self-contained breathing apparatus and full protective clothing must be worn in case of fire.

Fire fighting equipment/instructions
Move containers from fire area if you can do so without risk.

Specific methods
Use standard firefighting procedures and consider the hazards of other involved materials.

General fire hazards
No unusual fire or explosion hazards noted.

SECTION 6: Accidental release measures

Personal precautions, protective equipment and emergency procedures
Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Wear appropriate protective equipment and clothing during clean-up. Do not breathe dust. Use a NIOSH/MSHA approved respirator if there is a risk of exposure to dust/fume at levels exceeding the exposure limits. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Ensure adequate ventilation. Local authorities should be advised if significant spillages cannot be contained. For personal protection, see section 8 of the SDS.

Methods and materials for containment and cleaning up
Stop the flow of material, if this is without risk. If sweeping of a contaminated area is necessary use a dust suppressant agent which does not react with the product. Collect dust using a vacuum cleaner. Minimize dust generation and accumulation. Prevent entry into waterways, sewer, basements or confined areas. Following product recovery, flush area with water. For waste disposal, see section 13 of the SDS.

Environmental precautions
Avoid discharge into drains or water courses.

SECTION 7: Handling and storage

Precautions for safe handling
Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Provide appropriate exhaust ventilation at places where dust is formed. Minimize dust generation and accumulation. Do not breathe dust. Do not get this material in contact with eyes. Avoid prolonged exposure. Wear appropriate personal protective equipment. Observe good industrial hygiene practices.

Conditions for safe storage, including any incompatibilities
Store in original tightly closed container. Store in dry location. Store away from incompatible materials (see Section 10 of the SDS).

SECTION 8: Exposure controls/personal protection

US. OSHA Table Z-3 (29 CFR 1910.1000)

Components Type Value Form
Silica Quartz
(CAS 14808-60-7)
TWA
TWA
TWA
0.3 mg/m3
0.1 mg/m3
2.4 mppcf
Total dust
Respirable fraction
Respirable fraction
Methanal STEL
TWA
2 ppm
0.75 ppm
Respirable fraction
Respirable fraction

US. ACGIH Threshold Limit Values

Components Type Value Form
Silica, quartz
(CAS 14808-60-7)
TWA 0.025 mg/m3 Respirable fraction
Methanal CLV 0.3 ppm Respirable fraction

US. NIOSH: Pocket Guide to Chemical Hazards

Components Type Value Form
Silica, quartz
(CAS 14808-60-7)
TWA 0.05 mg/m3 Respirable fraction
Methanal TWA 0.016 ppm Respirable fraction

Biological limit values
No biological exposure limits noted for the ingredient(s).

Exposure guidelines
Occupational exposure to nuisance dust (total and respirable) and respirable crystalline silica should be monitored and controlled.

Appropriate engineering controls
Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level. Ventilation should be sufficient to effectively remove and prevent buildup of any dusts or fumes that may be generated during handling or thermal processing. If engineering measures are not sufficient to maintain concentrations of dust particulates below the Occupational Exposure Limit (OEL), suitable respiratory protection must be worn. Eye wash facilities and emergency shower must be available when handling this product.

Individual protection measures, such as personal protective equipment
Eye/face protection
Wear safety glasses or safety goggles unless full face respirator is in use.
Skin protection
Hand protection
Wear appropriate chemical resistant gloves.
Other
Wear appropriate chemical resistant clothing. Use of an impervious apron is recommended.
Respiratory protection
Use a NIOSH/MSHA approved respirator if there is a risk of exposure to dust/fume at levels exceeding the exposure limits.
Thermal hazards
Wear appropriate thermal protective clothing, when necessary.

General hygiene considerations
When using, do not eat, drink or smoke. Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. Observe any medical surveillance requirements.

SECTION 9: Physical and chemical properties

Basic Physical and Chemical Properties

Appearance
Physical state Solid.
Form Powder.
Colour Gray.
Odor Low.
Odor threshold Not available.
pH 11-12 when wet
Melting point/freezing point Not applicable.
Initial boiling point and boiling range Not applicable.
Flash point Not applicable.
Evaporation rate Not applicable.
Flammability (solid, gas) Non combustible.
Upper/lower flammability or explosive limits
Flammability limit – lower (%) Not applicable.
Flammability limit – upper (%) Not applicable.
Vapor pressure Not applicable.
Vapor density Not applicable.
Relative density 2.7-3.1 @ 20°C
Solubility(ies)
Solubility (water) Not available.
Partition coefficient (n-octanol/water) Not applicable.
Auto-ignition temperature Not applicable.
Decomposition temperature 2460 °F (1350 °C)
Viscosity Not applicable.
Other information
Bulk density 60 lb/ft3
Partition coefficient (oil/water) Not applicable.
VOC (Weight %) 0 g/L when mixed with water

SECTION 10: Stability and reactivity

Reactivity
The product is stable and non-reactive under normal conditions of use, storage and transport.

Chemical stability
Material is stable under normal conditions.

Possibility of hazardous reactions
No dangerous reaction known under conditions of normal use.

Conditions to avoid
Avoid temperatures exceeding the decomposition temperature. Contact with incompatible materials. Avoid dispersal of dust in the air (i.e., clearing dust surfaces with compressed air).

Incompatible materials
Powerful oxidizers.

Hazardous decomposition products
Carbon oxides. Sulfur oxides. Silicium oxide.

SECTION 11: Toxicological information

Information on likely routes of exposure
Inhalation
May cause damage to organs through prolonged or repeated exposure by inhalation. Inhalation of dusts may cause respiratory irritation. Prolonged inhalation may be harmful.
Skin contact
May cause skin irritation. Prolonged contact with wet cement/mixture may cause burns.
Eye contact
May cause serious eye damage. Prolonged contact with wet cement/mixture may cause burns.
Ingestion
Swallowing may cause gastrointestinal irritation.

Symptoms related to the physical, chemical and toxicological characteristics
Severe eye irritation. Symptoms may include stinging, tearing, redness, swelling, and blurred vision. Permanent eye damage including blindness could result. Upper respiratory tract irritation. Coughing. Discomfort in the chest. Shortness of breath. Wheezing. Skin irritation.

Information on toxicological effects
Acute toxicity
May cause respiratory irritation.
Skin corrosion/irritation
May cause skin irritation.
Serious eye damage/eye irritation
Causes serious eye damage.

Respiratory or skin sensitization
Respiratory sensitization
Based on available Data, the classification criteria are not met.
Skin sensitization
Based on available Data, the classification criteria are not met.

Germ cell mutagenicity
Based on available Data, the classification criteria are not met.

Carcinogenicity
May cause cancer.
In 1997, IARC (the International Agency for Research on Cancer) concluded that crystalline silica inhaled from occupational sources can cause lung cancer in humans. However in making the overall evaluation, IARC noted that “carcinogenicity was not detected in all industrial circumstances studied. Carcinogenicity may be dependent on inherent characteristics of the crystalline silica or on external factors affecting its biological activity or distribution of its polymorphs.” (IARC Monographs on the evaluation of the carcinogenic risks of chemicals to humans, Silica, silicates dust and organic fibres, 1997, Vol. 68, IARC, Lyon, France.) In June 2003, SCOEL (the EU Scientific Committee on Occupational Exposure Limits) concluded that the main effect in humans of the inhalation of respirable crystalline silica dust is silicosis. “There is sufficient information to conclude that the relative risk of lung cancer is increased in persons with silicosis (and, apparently, not in employees without silicosis exposed to silica dust in quarries and in the ceramic industry). Therefore, preventing the onset of silicosis will also reduce the cancer risk…” (SCOEL SUM Doc 94-final, June 2003) According to the current state of the art, worker protection against silicosis can be consistently assured by respecting the existing regulatory occupational exposure limits. Occupational exposure to respirable dust and respirable crystalline silica should be monitored and controlled.
IARC Monographs. Overall Evaluation of Carcinogenicity
NTP listed carcinogen.
Silica, quartz (CAS 14808-60-7)
1 Carcinogenic to Humans
Methanal (CAS 50-00-0)
1 Carcinogenic to Humans
The International Agency for Research on Cancer (IARC) has classified methanol as a Group 1 (known) human carcinogen based on epidemiological evidence linking methanol exposure to occurrence of nasopharyngeal cancer and leukemia. Current regulatory information is provided in this SDS. No adverse health effects are anticipated if recommended personal protective equipment and industrial hygiene practices are used.
NTP Report on Carcinogens
Silica, quartz (CAS 14808-60-7)
Known to be human carcinogen
Methanal (CAS 50-00-0)
Known to be human carcinogen
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050)
Not listed.

Reproductive toxicity
May damage fertility or the unborn child.

Specific target organ toxicity – single exposure
May cause respiratory irritation.

Specific target organ toxicity – repeated exposure
May cause damage to organs (Lungs) through prolonged or repeated exposure.

Aspiration hazard
Due to the physical form of the product it is not an aspiration hazard.

Chronic effects
Prolonged or repeated exposure may cause lung injury, including silicosis. May cause skin disorders if contact is repeated or prolonged.

SECTION 12: Ecological information

Ecotoxicity
The product is not classified as environmentally hazardous. However, this does not exclude the possibility that large or frequent spills can have a harmful or damaging effect on the environment.

ACUTE TOXICITY TO FISH: COMPONENTS

Components Species Test Results
Methanal LEUCISCUS IDUS LC50 (48 HRS) > 560 mg/l

 

ACUTE TOXICITY TO AQUATIC INVERTEBRATES: COMPONENTS

Components Species Test Results
Methanal DAPHNIA MAGNA EC50 (48 HRS) > 33.1 mg/l

 

ACUTE TOXICITY TO BACTERIA: COMPONENTS

Components Species Test Results
Methanal BACTERIUM EC10: 1800 mg/l

 

Persistence and degradability
No data available.

Bioaccumulative potential
No data available.

Mobility in soil
No data available.

Other adverse effects
No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation potential, endocrine disruption, global warming potential) are expected from this component.

SECTION 13: Disposal considerations

Disposal instructions
Collect and reclaim or dispose in sealed containers at licensed waste disposal site. Dispose of contents/container in accordance with local/regional/national/international regulations.

Local disposal regulations
Dispose in accordance with all applicable regulations.

Hazardous waste code
The waste code should be assigned in discussion between the user, the producer and the waste disposal company.

Waste from residues / unused products
Dispose of in accordance with local regulations. Empty containers or liners may retain some product residues. This material and its container must be disposed of in a safe manner (see: Disposal instructions).

Contaminated packaging
Empty containers should be taken to an approved waste handling site for recycling or disposal. Since emptied containers may retain product residue, follow label warnings even after container is emptied.

SECTION 14: Transportation information

DOT
Not regulated as dangerous goods.

IATA
Not regulated as dangerous goods.

IMDG
Not regulated as dangerous goods.

Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
Not applicable.

SECTION 15: Regulatory information

US federal regulations
This product is a “Hazardous Chemical” as defined by the OSHA Hazard Communication Standard, 29 CFR 1910.1200.
TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)
Not regulated.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050)
Not listed.
CERCLA Hazardous Substance List (40 CFR 302.4)
CERCLA RQ
100 LBS
CAS Number
50-00-0
Chemical name
Methanal

Superfund Amendments and Reauthorization Act of 1986 (SARA) Hazard categories
Immediate Hazard – Yes
Delayed Hazard – Yes
Fire Hazard – No
Pressure Hazard – No
Reactivity Hazard – No
SARA 311/312 Hazardous chemical
Yes
SARA 313 (TRI reporting)
Not regulated.

Other federal regulations
Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List
Not regulated.
Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)
Not regulated.
Safe Drinking Water Act (SDWA)
Not regulated.

US state regulations
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
US. Massachusetts RTK – Substance List

Chemical name CAS number Concentration
Silica, quartz 14808-60-7 30-50%
Methanal 50-00-0 <= 0.05%

US. New Jersey Worker and Community Right-to-Know Act

Chemical name CAS number Concentration
Silica, quartz 14808-60-7 30-50%
Methanal 50-00-0 <= 0.05%

US. Pennsylvania Worker and Community Right-to-Know Law

Chemical name CAS number Concentration
Silica, quartz 14808-60-7 30-50%
Methanal 50-00-0 <= 0.05%

US. California Proposition 65
US – California Proposition 65 – Carcinogens & Reproductive Toxicity (CRT): Listed substance
Silica, quartz (CAS 14808-60-7)
Methanal (CAS 50-00-0)
WARNING CANCER and REPRODUCTIVE HARM – www.P65Warnings.ca.gov

International Inventories
Country(s) or region
United States & Puerto Rico
Inventory name
Toxic Substances Control Act (TSCA) Inventory
On inventory (yes/no)*
Yes

*A “Yes” indicates this product complies with the inventory requirements administered by the governing country(s).
A “No” indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing country(s).

SECTION 16: Other information, including date of preparation or last revision

Issue date 27-November-2018
Revision date
Version # 02
HMIS® ratings Health: 3
Flammability: 0
Physical hazard: 0

 

Disclaimer

CTS Cement Manufacturing Corporation cannot anticipate all conditions under which this information and its product, or the products of other manufacturers in combination with its product, may be used. It is the user’s responsibility to ensure safe conditions for handling, storage and disposal of the product, and to assume liability for loss, injury, damage or expense due to improper use. The information in the sheet was written based on the best knowledge and experience currently available.


Product Calculator


How Much Do I Need?

Calculate how much of a product you need, then add it to your Shopping List.
Jump To Calculator Icon

Jump To Calculator

More Information

King Packaged Materials Company offers this product in a 25 lb box.