SAKRETE brush’n seal

Create a protective coating and decorative finish for concrete or brick! Use SAKRETE brush’n seal, a dual-purpose, moisture sealant. Available in 5 KG pails. Go with SAKRETE, The Pro’s Choice since 1936.

Product Code: 12251005

• Premium quality, heavy-duty, multi-purpose product
• Waterproof, seal or decorate concrete, concrete block, brick and masonry surfaces
• Damp-proof basement walls and foundations
• Suitable for interior and exterior applications, above or below grade
• Dries to a medium-white finish and can be painted with latex paint


1. FEATURES & BENEFITS

• Moisture sealant for masonry surfaces
• Dries white
• May be applied to painted concrete

2. USES

Ideal for waterproofing and sealing basement walls, foundations, swimming pools and cisterns. Can also be applied as a decorative finish to all types of concrete and masonry surfaces.

3. PROCEDURES

Mix and substrate temperatures should be maintained between 5 ºC and 30 ºC (40 ºF and 86 ºF) for at least 24 hours prior to and 48 hours after.

Surface Preparation: Surfaces to be coated must be structurally sound and clean. Remove all delaminated or unsound concrete by chipping with a hammer and chisel or using a stiff wire brush. Repair all cracks and holes with SAKRETE plug-tite. Remove any dirt, sand, dust or paint by sweeping, vacuuming, scraping or wire brushing as required. For walls previously painted with anything other than a cement-based paint use a scraper or wire brush and remove as much material as possible to create a good bond. The more paint removed the better the bond. Remove all efflorescence, mold, grease or oil by scrubbing vigorously with a strong detergent solution and flood with large volumes of potable water. Clean the area to be repaired with potable water, leaving the concrete saturated but free of standing water. Some very porous concretes may require several applications of water to ensure complete saturation.

Mixing: Mix approximately 293 mL (10 oz) of potable water per 1 KG (2.2 lb) of product. In a disposable plastic pail, put 1/2 of the required water into pail first, add the product and then add balance of the required water. Mix to a pancake batter consistency and then allow the mix to sit for 5 to 10 minutes before applying (avoid a “soupy” mix). A proper mixture should adhere to the brush without dripping. NOTE: For painted surfaces, replace at least 1/3 of the required mixing water with SAKRETE Concrete Adhesive. This will further help the SAKRETE brush’n seal mix to adhere to the original surface.

Placing: Dampen walls one hour before application of SAKRETE brush’n seal and allow the moisture to soak in. Immediately prior to application, the surface should be damp, but not dripping. Maintain this damp surface during the entire application. When ready to begin application, a small amount of water may be added if required to bring the mixture to a batter like consistency. Stir mix occasionally during application. After mixing, apply SAKRETE brush’n seal with a semi-stiff nylon bristle brush. Scrub the mix well into the existing surface, ensuring you fill all the pores, and then finish with a final stroke in one direction. For a decorative appearance, mixture can be finished with a sponge or float. If wall becomes dry or mix starts to pull during application, dampen the original surface again. Do not add more water to the mixture. For normal waterproofing, a two-coat application is recommended. Allow the first coat to cure for 24 hours then dampen surface and apply second coat.

4. CURING

Allow application to harden sufficiently (approximately 3 hours) then fog spray with clean water. Keep the surface continuously damp for 3 days. This step is critical during hot or windy days.

5. PAINTING

Product must be fully cured (approximately 28 days) and dry before painting. Refer to paint manufacturer directions for application instructions.

6. YIELD

1 KG (2.2 lb) yields approximately 0.93 m² (10 ft²).

7. SAFETY PROCEDURES

CAUSES BURNS. Do not swallow. Do not get in eyes. Do not get on skin or clothing. Do not breathe fumes. Handle with care. Keep out of reach of children. Wear safety glasses, protective clothing and dust mask. Use only in a well-ventilated area.

FIRST AID TREATMENT: Contains cement, when wet forms a calcium hydroxide solution. If swallowed call a poison control center or doctor immediately. Do not induce vomiting. If in eyes, rinse with water for at least 15 minutes. If on skin, rinse well with water. If on clothes remove clothes. If breathed in, move person to fresh air.

Warranty

This product is designed to meet the performance specifications outlined in this product data sheet. If the product is used in conditions for which it was not intended, or applied in a manner contrary to the written recommendations contained in the product data sheet, the product may not reach such performance specifications. The foregoing is in lieu of any other warranties, representations or conditions, expressed or implied, including, but not limited to, implied warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade.

Create a protective coating and decorative finish for concrete or brick! Use SAKRETE brush’n seal, a dual-purpose, moisture sealant. Available in 5 KG pails. Go with SAKRETE, The Pro’s Choice since 1936.

Product Code: 12251005

• Premium quality, heavy-duty, multi-purpose product
• Waterproof, seal or decorate concrete, concrete block, brick and masonry surfaces
• Damp-proof basement walls and foundations
• Suitable for interior and exterior applications, above or below grade
• Dries to a medium-white finish and can be painted with latex paint


SECTION 1: IDENTIFICATION

Product Identifier

Concrete and Masonry Repair Mixes

Other Means of Identification Concrete and Masonry Repair Mixes
Other Identification SAKRETE top’n bond, SAKRETE flow-stone, SAKRETE fast-patch, SAKRETE plug-tite, SAKRETE brush’n seal, KING Xypex high’n dry
Product Family KING Home Improvement Products
Recommended Use

Various product uses including but not limited to specific description of use. Please see product packaging.

Restrictions on Use None known.
Manufacturer

King Packaged Materials Company, 3385 Harvester Road, Burlington, Ontario, L7R 3Y5, www.kpmindustries.com

Emergency Phone No. King Packaged Materials Company, (800) 461-0566, 8:30am-4:30pm, Chemtrec, (800) 424-9300, 24 hours/7 days a week
SDS No. 0156
Date of Preparation April 05, 2016

SECTION 2: HAZARD IDENTIFICATION

Classification
Skin irritation – Category 2; Serious eye damage – Category 1; Skin sensitization – Category 1; Carcinogenicity – Category 1A; Specific target organ toxicity (single exposure) – Category 3; Specific target organ toxicity (repeated exposure) – Category 1

Label Elements

Signal Word:
Danger

Hazard Statement(s):
Causes skin irritation.
Causes serious eye damage.
May cause an allergic skin reaction.
May cause cancer.
May cause respiratory irritation.
Causes damage to organs (lungs) through prolonged or repeated exposure.

Precautionary Statement(s):
Obtain special instructions before use.
Do not handle until all safety precautions have been read and understood.
Wash hands thoroughly after handling.
Contaminated work clothing must not be allowed out of the workplace.
Wear protective gloves/protective clothing/eye protection/face protection.
Use only outdoors or in a well-ventilated area.
Do not breathe dust/fume/gas/mist/vapours/spray.
Do not eat, drink or smoke when using this product.

IF exposed or concerned: Get medical advice/attention.
IF ON SKIN: Wash with plenty of water.
Take off contaminated clothing and wash it before reuse.
If skin irritation or rash occurs: Get medical advice/attention.
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTRE or doctor.
IF INHALED: Remove person to fresh air and keep comfortable for breathing.

Call a POISON CENTRE or doctor if you feel unwell.
Store locked up.
Store in a well-ventilated place. Keep container tightly closed.
Dispose of contents and container in accordance with local, regional, national and international regulations.
30% of the mixture consists of ingredient(s) of unknown acute toxicity.

Other Hazards
None known.

SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS

Mixture:

Chemical Name CAS Registry No. Concentration % Other Identifiers
Silica, total quartz 14808-60-7 60-100% Not applicable
Portland cement 65997-15-1 30-60% Not appliable

 

Notes
The exact percentage (concentration) of composition has been withheld as a trade secret in accordance with paragraph (i) of §1910.1200.

SECTION 4: FIRST-AID MEASURES

First-Aid Measures

Inhalation
Move to fresh air. Keep at rest in a position comfortable for breathing. Call a Poison Centre or doctor if you feel unwell.
Skin Contact
Rinse with lukewarm, gently flowing water for 5 minutes. Take off immediately contaminated clothing, shoes and leather goods (e.g. watchbands, belts). Thoroughly clean clothing, shoes and leather goods before reuse or dispose of safely. If skin irritation or a rash occurs, get medical advice or attention.
Eye Contact
Immediately rinse the contaminated eye(s) with lukewarm, gently flowing water for 15-20 minutes, while holding the eyelid(s) open. Remove contact lenses, if present and easy to do. Immediately call a Poison Centre or doctor.
Ingestion
Never give anything by mouth if person is rapidly losing consciousness, or is unconscious or convulsing. Do not induce vomiting. Get medical advice or attention if you feel unwell or are concerned.

Most Important Symptoms and Effects, Acute and Delayed
If inhaled: can irritate the nose and throat. Can cause lung injury. If on skin: skin sensitizer. May cause an allergic skin reaction in some people. May cause moderate to severe irritation. If in eyes: causes moderate to severe irritation. Symptoms include sore, red eyes, and tearing. If swallowed: can irritate the mouth, throat and stomach. Symptoms may include nausea, vomiting, stomach cramps and diarrhea.

Immediate Medical Attention and Special Treatment

Special Instructions
Not applicable.

SECTION 5: FIRE-FIGHTING MEASURES

Extinguishing Media

Suitable Extinguishing Media
Not combustible. Use extinguishing agent suitable for surrounding fire.
Unsuitable Extinguishing Media
None known.

Specific Hazards Arising from the Product
This product presents no unusual hazards in a fire situation.

Special Protective Equipment and Precautions for Fire-Fighters
Approach fire from upwind to avoid hazardous vapours or gases. Fire-fighters may enter the area if positive pressure SCBA and full Bunker Gear is worn.

SECTION 6: ACCIDENTAL RELEASE MEASURES

Personal Precautions, Protective Equipment, and Emergency Procedures
Use the personal protective equipment recommended in Section 8 of this safety data sheet. Evacuate the area immediately. Isolate the hazard area. Keep out unnecessary and unprotected personnel.

Environmental Precautions
It is good practice to prevent releases into the environment. Do not allow into any sewer, on the ground or into any waterway.

Methods and Materials for Containment and Cleaning Up
Collect using shovel/scoop or approved HEPA vacuum and place in a suitable container for disposal. Avoid generating dust.

SECTION 7: HANDLING AND STORAGE

Precautions for Safe Handling
Avoid repeated or prolonged skin contact. Do not swallow. Do not breathe in this product. Avoid generating dusts. Keep containers tightly closed when not in use or empty. Do NOT eat, drink or store food in work areas.

Conditions for Safe Storage
Store in the original, labelled, shipping container. Store in an area that is: dry, well-ventilated. Protect product from contact with water, including humidity. Prevent rainwater and ground water from reaching storage area.

SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION

Control Parameters

ACGIH TLV®

OSHA PEL

AIHA WEEL

Chemical Name

TWA

STEL

TWA

Ceiling

8-hr TWA

TWA

Silica, total quartz

0.05 mg/m3
(R) A2

0.1 mg/m3

Portland cement

1 mg/m3
(R) A4

5 mg/m3
(R)

 

Appropriate Engineering Controls
Use local exhaust ventilation, if general ventilation is not adequate to control amount in the air.

Individual Protection Measures

Eye/Face Protection
Wear chemical safety goggles and face shield when contact is possible.
Skin Protection
Wear chemical protective clothing e.g. gloves, aprons, boots.
Respiratory Protection
Wear a NIOSH approved particulate respiratory equipped with an N95, R95, or P95 filter.

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

Basic Physical and Chemical Properties

Appearance Grey powder
Odour

Odourless

Odour Threshold

Not available

pH

Not available

Melting Point/Freezing Point Not available (melting); Not available (freezing)

Initial Boiling Point/Range

Not available

Flash Point

Not available

Evapouration Point

Not available

Flammability (solid, gas)

Not applicable

Upper/Lower Flammability or Explosive Limit

Not available (upper); Not available (lower)

Vapour Pressure

Not available

Vapour Density (air = 1)

Not available

Relative Density (water = 1)

2.5

Solubility

Not available (water); Not available (other liquids)

Partition Coefficient, n-Octanol/Water (Log Kow)

Not available

Auto-ignition Temperature

Not available

Decomposition Temperature

Not available

Viscosity

Not available (kinematic); Not available (dynamic)

Physical State

Solid

 

SECTION 10: STABILITY AND REACTIVITY

Reactivity
Not reactive under normal conditions of use.

Chemical Stability
Normally stable.

Possibility of Hazardous Reactions
None expected under normal conditions of storage and use.

Conditions to Avoid
Water, moisture or humidity.

Incompatible Materials
None known.

Hazardous Decomposition Products
Under normal conditions of storage and use, hazardous decomposition products should not be produced.

SECTION 11: TOXICOLOGICAL INFORMATION

Likely Routes of Exposure
Inhalation; skin contact; eye contact; ingestion.

Acute Toxicity

Chemical Name LC50 LD50 (oral) LD50 (dermal)
Silica, total quartz 500 mg/kg (rat)

 

Skin Corrosion/Irritation
May cause moderate or severe irritation based on information for closely related materials.
Serious Eye Damage/Irritation
May cause serious eye damage based on information for closely related materials.

STOT (Specific Target Organ Toxicity) – Single Exposure

Inhalation
May cause severe nose and throat irritation, severe lung injury.
Skin Absorption
No information was located.
Ingestion
May be harmful based on information for closely related materials.

Aspiration Hazard
Can cause lung damage if aspirated based on human experience.

STOT (Specific Target Organ Toxicity) – Repeated Exposure
Causes irritation of the respiratory system. Respiratory tract injury has been observed. Respirable crystalline silica in the form of quartz or cristobalite from occupational sources is listed by the International Agency for Research on Cancer (IARC) and National Toxicology Program (NTP) as a lung carcinogen. Prolonged exposure to respirable crystalline silica has been known to cause silicosis, a lung disease, which may be disabling. While there may be a factor of individual susceptibility to a given exposure to respirable silica dust, the risk of contracting silicosis and the severity of the disease is clearly related to the amount of dust exposure and the length of time (usually years) of exposure.

Respiratory and/or Skin Sensitization
May cause an allergic reaction (skin sensitization) based on information for closely related chemicals.

Carcinogenicity

Chemical Name IARC ACGIH® NTP OSHA
Silica, total quartz Group 1 A1 Known carcinogen

 

May causer cancer.

Reproductive Toxicity

Development of Offspring
No information was located.
Sexual Function and Fertility
No information was located.
Effects on or via Lactation
No information was located.

Germ Cell Mutagenicity
No information was located.
Interactive Effects
No information was located.

SECTION 12: ECOLOGICAL INFORMATION

Ecotoxicity
May cause long lasting harmful effects to aquatic life.

Persistence and Degradability
No information was located.

Bioaccumulative Potential
No information was located.

Mobility in Soil
No information was located.

Other Adverse Effects
There is no information available.

SECTION 13: DISPOSAL CONSIDERATIONS

Disposal Methods
Contact local environmental authorities for approved disposal or recycling methods in your jurisdiction

SECTION 14: TRANSPORT INFORMATION

Not regulated under US DOT Regulations.

Environmental Hazards
Not applicable
Special Precautions
Not applicable

Transport in Bulk According to Annex II of MARPOL 73/78 and the IBC Code
Not applicable

SECTION 15: REGULATORY INFORMATION

Safety, Health and Environmental Regulations
Canada

WHMIS 1988 Classification

Class D2A, Class E
D2A – Very Toxic (Chronic toxicity; Carcinogenicity); E – Corrosive

This product has been classified in accordance with the hazard criteria of the Controlled Products Regulations and the SDS contains all of the information required by the Controlled Products Regulations.

USA

Toxic Substances Control Act (TSCA) Section 8(b)
All ingredients are on the TSCA Inventory or are exempt from TSCA Inventory requirements under 40 CFR 720.
Additional USA Regulatory Lists
This product contains a chemical known to the State of California to cause cancer.

SECTION 16: OTHER INFORMATION

SDS Prepared By King Packaged Materials Company
Phone No. 905-639-2993
Date of Preparation April 05, 2016

 

Disclaimer

To the best of our knowledge, the information contained herein is accurate. However, neither KPM Industries Ltd., nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist.


Product Calculator


How Much Do I Need?

Calculate how much of a product you need, then add it to your Shopping List.
Jump To Calculator Icon

Jump To Calculator


How-To Video

Read the How-To Instructions

CLICK HERE >

More Information

PLEASE NOTE: This product was previously known as KING brush'n seal.

SAKRETE brush’n seal can be used to waterproof masonry surfaces that develop dampness from water. Learn how to waterproof concrete, by viewing the Flash Player clip or reading the how-to instructions.