SAKRETE ICF 5000

Parge or coat above-grade ICF block walls! Use this cement-based material to finish Insulated Concrete Form (ICF) block walls or other Expanded Polystyrene Surfaces (EPS). This product is designed to be applied to above-grade portions of ICF foundation walls with a maximum, single coat thickness of 3 mm (1/8”)*. Available in 22.7 KG bags. Go with SAKRETE, The Pro’s Choice since 1936.

Product Code: 11501125

• Provides excellent bonding to ICF walls or other EPS surfaces
• Protects EPS from weathering and UV degradation
• Allows for easy troweling and smooth finishing
• Allows for simple embedment of fiberglass mesh
• Reaches a compressive strength of 34 MPa (5000 psi) in 28 days
• Ready to use; just add water


1. FEATURES & BENEFITS

• Easy troweling and smooth finishing allows for simple embedment of fiberglass mesh
• Excellent bonding to ICF walls or other EPS surfaces

2. USES

Parging or coating above-grade ICF walls, to protect EPS from weathering and UV degradation.

3. PROCEDURES

Mix and substrate temperatures should be maintained between 5 °C (40 °F) and 30 °C (86 °F) for at least 24 hours prior to and 48 hours after application. Avoid applying SAKRETE ICF 5000 in direct sunlight or when winds exceed 25 km/hour (15 mph). Protect from precipitation for 24 hours after application.

Mixing: Add 3.7 L (0.98 US gallons) to 3.9 L (1.03 US gallons) of cool, potable water into a clean mixing container. Slowly empty the 22.7 KG (50 lb) bag of SAKRETE ICF 5000 into the container while mixing with a heavy-duty, 13 mm (1/2”), electric drill and mixing paddle. After all of the powder has been added, thoroughly mix the material for 3 minutes.

Placing: Apply a 3 mm (1/8”) coat of SAKRETE ICF 5000 using a stainless steel trowel, directly to the ICF wall. Immediately embed alkali-resistant fiberglass mesh into the first coat, ensuring that the mesh joints overlap by a minimum of 65 mm (2½”) and that the mesh is doubled at all corners as well as corners of openings (e.g. windows and doors). Apply additional 3 mm (1/8”) coats of SAKRETE ICF 5000 as needed, in order to completely cover and embed the fiberglass mesh, up to a maximum total thickness of 9 mm (3/8″)*.

Finishing: For a smooth surface, use a stainless steel, wood, aluminum or magnesium trowel. For a textured surface, use a broom, brush or dry sponge.

4. CURING

Under most conditions, SAKRETE ICF 5000 requires no special curing. Protect the surface of SAKRETE ICF 5000 with plastic if precipitation or winds in excess of 25 km/hour (15 mph) are expected within 24 hours after application. Mix and substrate temperatures should be maintained between 5 °C (40 °F) and 30 °C (86 °F) for at least 24 hours prior to and 48 hours after application.

5. TECHNICAL DATA

Initial Set: Approximately 6 hours

Compressive Strength

1 Day 10 MPa (1500 psi)
3 Day 21 MPa (3000 psi)
7 Day 25 MPa (3625 psi)
28 Day 34 MPa (5000 psi)

6. YIELD

22.7 KG (50 lb) bag contains approximately 0.013 m3 (0.46 ft3).

Thickness Coverage
3 mm (1/8″) 4.30 m2 (46.0 ft2)
6 mm (1/4″) 2.15 m2 (23.0 ft2)
9 mm (3/8″) 1.45 m2 (15.6 ft2)

 

7. STORAGE & SHELF LIFE

Material should be stored in a dry, covered area, protected from the elements. Unopened bags have a shelf life of 12 months.

8. SAFETY PROCEDURES

CAUSES BURNS. Do not swallow. Do not get in eyes. Do not get on skin or clothing. Do not breathe fumes. Handle with care. Keep out of reach of children. Wear safety glasses, protective clothing and dust mask. Use only in a well-ventilated area.

FIRST AID TREATMENT: Contains cement, when wet forms a calcium hydroxide solution. If swallowed call a poison control center or doctor immediately. Do not induce vomiting. If in eyes, rinse with water for at least 15 minutes. If on skin, rinse well with water. If on clothes remove clothes. If breathed in, move person to fresh air.

Warranty

This product is designed to meet the performance specifications outlined in this product data sheet. If the product is used in conditions for which it was not intended, or applied in a manner contrary to the written recommendations contained in the product data sheet, the product may not reach such performance specifications. The foregoing is in lieu of any other warranties, representations or conditions, expressed or implied, including, but not limited to, implied warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade.

Parge or coat above-grade ICF block walls! Use this cement-based material to finish Insulated Concrete Form (ICF) block walls or other Expanded Polystyrene Surfaces (EPS). This product is designed to be applied to above-grade portions of ICF foundation walls with a maximum, single coat thickness of 3 mm (1/8”)*. Available in 22.7 KG bags. Go with SAKRETE, The Pro’s Choice since 1936.

Product Code: 11501125

• Provides excellent bonding to ICF walls or other EPS surfaces
• Protects EPS from weathering and UV degradation
• Allows for easy troweling and smooth finishing
• Allows for simple embedment of fiberglass mesh
• Reaches a compressive strength of 34 MPa (5000 psi) in 28 days
• Ready to use; just add water


SECTION 1: IDENTIFICATION

Product Identifier SAKRETE ICF 5000
Other Means of Identification SAKRETE ICF 5000
Product Family KING Home Improvement Products
Recommended Use For parging or coating above-grade ICF walls to protect EPS from weathering and UV degradation.
Restrictions on Use None known.
Manufacturer King Packaged Materials Company, 3385 Harvester Road, Burlington, Ontario, L7R 3Y5, www.kpmindustries.com
Emergency Phone No. King Packaged Materials Company, (800) 461-0566, 8:30am-4:30pm, Chemtrec, (800) 424-9300, 24 hours/7 days a week
SDS No. 0471
Date of Preparation December 7, 2018

SECTION 2: HAZARD IDENTIFICATION

Classification
Skin irritation – Category 2; Serious eye damage – Category 1; Skin sensitization – Category 1; Carcinogenicity – Category 1A; Specific target organ toxicity (single exposure) – Category 3; Specific target organ toxicity (repeated exposure) – Category 1

Label Elements

Signal Word:
Danger

Hazard Statement(s):
Causes skin irritation.
Causes serious eye damage.
May cause an allergic skin reaction.
May cause cancer.
May cause respiratory irritation.
Causes damage to organs (lungs) through prolonged or repeated exposure.

Precautionary Statement(s):
Obtain special instructions before use.
Do not handle until all safety precautions have been read and understood.
Wash hands thoroughly after handling.
Contaminated work clothing must not be allowed out of the workplace.
Wear protective gloves/protective clothing/eye protection/face protection.
Use only outdoors or in a well-ventilated area.
Do not breathe dust/fume/gas/mist/vapours/spray.
Do not eat, drink or smoke when using this product.

IF exposed or concerned: Get medical advice/attention.
IF ON SKIN: Wash with plenty of water.
Take off contaminated clothing and wash it before reuse.
If skin irritation or rash occurs: Get medical advice/attention.
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTRE or doctor.
IF INHALED: Remove person to fresh air and keep comfortable for breathing.

Call a POISON CENTRE or doctor if you feel unwell.
Store locked up.
Store in a well-ventilated place. Keep container tightly closed.
Dispose of contents and container in accordance with local, regional, national and international regulations.
10% of the mixture consists of ingredient(s) of unknown acute toxicity.

Other Hazards
None known.

SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS

Mixture:

Chemical Name CAS Registry No. Concentration % Other Identifiers
Silica, total quartz 14808-60-7 60-100% Not applicable
Portland cement 65997-15-1 15-45% Not applicable
Hydrated lime 58398-71-3 1-5% Not applicable

 

Notes
The exact percentage (concentration) of composition has been withheld as a trade secret in accordance with paragraph (i) of §1910.1200.

SECTION 4: FIRST-AID MEASURES

First-Aid Measures

Inhalation
Move to fresh air. Keep at rest in a position comfortable for breathing. Call a Poison Centre or doctor if you feel unwell.
Skin Contact
Rinse with lukewarm, gently flowing water for 5 minutes. Take off immediately contaminated clothing, shoes and leather goods (e.g. watchbands, belts). Thoroughly clean clothing, shoes and leather goods before reuse or dispose of safely. If skin irritation or a rash occurs, get medical advice or attention.
Eye Contact
Immediately rinse the contaminated eye(s) with lukewarm, gently flowing water for 15-20 minutes, while holding the eyelid(s) open. Remove contact lenses, if present and easy to do. Immediately call a Poison Centre or doctor.
Ingestion
Never give anything by mouth if person is rapidly losing consciousness, or is unconscious or convulsing. Do not induce vomiting. Get medical advice or attention if you feel unwell or are concerned.

Most Important Symptoms and Effects, Acute and Delayed
If inhaled: can irritate the nose and throat. Can cause lung injury. If on skin: skin sensitizer. May cause an allergic skin reaction in some people. May cause moderate to severe irritation. If in eyes: causes moderate to severe irritation. Symptoms include sore, red eyes, and tearing. If swallowed: can irritate the mouth, throat and stomach. Symptoms may include nausea, vomiting, stomach cramps and diarrhea.

Immediate Medical Attention and Special Treatment

Special Instructions
Not applicable.

SECTION 5: FIRE-FIGHTING MEASURES

Extinguishing Media

Suitable Extinguishing Media
Not combustible. Use extinguishing agent suitable for surrounding fire.
Unsuitable Extinguishing Media
None known.

Specific Hazards Arising from the Product
This product presents no unusual hazards in a fire situation.

Special Protective Equipment and Precautions for Fire-fighters
Approach fire from upwind to avoid hazardous vapours or gases. Fire-fighters may enter the area if positive pressure SCBA and full Bunker Gear is worn.

SECTION 6: ACCIDENTAL RELEASE MEASURES

Personal Precautions, Protective Equipment, and Emergency Procedures
Use the personal protective equipment recommended in Section 8 of this safety data sheet. Evacuate the area immediately. Isolate the hazard area. Keep out unnecessary and unprotected personnel.

Environmental Precautions
It is good practice to prevent releases into the environment. Do not allow into any sewer, on the ground or into any waterway.

Methods and Materials for Containment and Cleaning Up
Collect using shovel/scoop or approved HEPA vacuum and place in a suitable container for disposal. Avoid generating dust.

 

SECTION 7: HANDLING AND STORAGE

Precautions for Safe Handling
Avoid repeated or prolonged skin contact. Do not swallow. Do not breathe in this product. Avoid generating dusts. Keep containers tightly closed when not in use or empty. Do NOT eat, drink or store food in work areas.

Conditions for Safe Storage
Store in the original, labelled, shipping container. Store in an area that is: dry, well-ventilated. Protect product from contact with water, including humidity. Prevent rainwater and ground water from reaching storage area.

SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION

Control Parameters

ACGIH TLV®

OSHA PEL

AIHA WEEL

Chemical Name

TWA

STEL

TWA

Ceiling

8-hr TWA

TWA

Portland cement

1 mg/m3
(R) A4

5 mg/m3
(R)

Silica, total quartz

0.05 mg/m3
(R) A2

0.1 mg/m3

 

Appropriate Engineering Controls
Use local exhaust ventilation, if general ventilation is not adequate to control amount in the air.

Individual Protection Measures

Eye/Face Protection
Wear chemical safety goggles and face shield when contact is possible.
Skin Protection
Wear chemical protective clothing e.g. gloves, aprons, boots.
Respiratory Protection
Wear a NIOSH approved particulate respiratory equipped with an N95, R95, or P95 filter.

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

Basic Physical and Chemical Properties

Appearance Grey powder
Odour Odourless
Odour Threshold Not available
pH Not available
Melting Point/Freezing Point Not available (melting); not available (freezing)
Initial Boiling Point/Range Not available
Flash Point Not available
Evapouration Rate Not available
Flammability (solid, gas) Not applicable
Upper/Lower Flammability or Explosive Limit Not available (upper); not available (lower)
Vapour Pressure Not available
Vapour Density (air = 1) Not available
Relative Density (water = 1) 2.5
Solubility Not available (in water); not available (in other liquids)
Partition Coefficient, n-Octanol/Water (Log Kow) Not available
Auto-ignition Temperature Not available
Decomposition Temperature  Not available
Viscosity Not available (kinematic); Not available (dynamic)
Physical State Solid

SECTION 10: STABILITY AND REACTIVITY

Reactivity
Not reactive under normal conditions of use.

Chemical Stability
Normally stable.

Possibility of Hazardous Reactions
None expected under normal conditions of storage and use.

Conditions to Avoid
Water, moisture or humidity.

Incompatible Materials
None known.

Hazardous Decomposition Products
Under normal conditions of storage and use, hazardous decomposition products should not be produced.

SECTION 11: TOXICOLOGICAL INFORMATION

Likely Routes of Exposure
Inhalation; skin contact; eye contact; ingestion.

Acute Toxicity

Chemical Name LC50 LD50 (oral) LD50 (dermal)
Silica, total quartz 500 mg/kg (rat)

 

Skin Corrosion/Irritation
May cause moderate or severe irritation based on information for closely related materials.
Serious Eye Damage/Irritation
May cause serious eye damage based on information for closely related materials.

STOT (Specific Target Organ Toxicity) – Single Exposure

Inhalation
May cause severe nose and throat irritation, severe lung injury.
Skin Absorption
No information was located.
Ingestion
May be harmful based on information for closely related materials.

Aspiration Hazard
Can cause lung damage if aspirated based on human experience.

STOT (Specific Target Organ Toxicity) – Repeated Exposure
Causes irritation of the respiratory system. Respiratory tract injury has been observed. Respirable crystalline silica in the form of quartz or cristobalite from occupational sources is listed by the International Agency for Research on Cancer (IARC) and National Toxicology Program (NTP) as a lung carcinogen. Prolonged exposure to respirable crystalline silica has been known to cause silicosis, a lung disease, which may be disabling. While there may be a factor of individual susceptibility to a given exposure to respirable silica dust, the risk of contracting silicosis and the severity of the disease is clearly related to the amount of dust exposure and the length of time (usually years) of exposure.

Respiratory and/or Skin Sensitization
May cause an allergic reaction (skin sensitization) based on information for closely related chemicals.

Carcinogenicity

Chemical Name IARC ACGIH® NTP OSHA
Silica, total quartz Group 1 A2 Known carcinogen

 

May cause cancer.

Reproductive Toxicity

Development of Offspring
No information was located.
Sexual Function and Fertility
No information was located.
Effects on or via Lactation
No information was located.
Germ Cell Mutagenicity
No information was located.
Interactive Effects
No information was located.

SECTION 12: ECOLOGICAL INFORMATION

Ecotoxicity
May cause long lasting harmful effects to aquatic life.

Persistence and Degradability
No information was located.

Bioaccumulative Potential
No information was located.

Mobility in Soil
No information was located.

Other Adverse Effects
There is no information available.

SECTION 13: DISPOSAL CONSIDERATIONS

Disposal Methods
Contact local environmental authorities for approved disposal or recycling methods in your jurisdiction.

SECTION 14: TRANSPORT INFORMATION

Not regulated under US DOT Regulations.

Environmental Hazards
Not applicable
Special Precautions
Not applicable

Transport in Bulk According to Annex II of MARPOL 73/78 and the IBC Code
Not applicable

SECTION 15: REGULATORY INFORMATION

Safety, Health and Environmental Regulations
Canada

WHMIS 1988 Classification

Class D2A, Class E
D2A – Very Toxic (Chronic toxicity; Carcinogenicity); E – Corrosive

This product has been classified in accordance with the hazard criteria of the Controlled Products Regulations and the SDS contains all of the information required by the Controlled Products Regulations.

USA

Toxic Substances Control Act (TSCA) Section 8(b)
All ingredients are on the TSCA Inventory or are exempt from TSCA Inventory requirements under 40 CFR 720.

Additional USA Regulatory Lists
This product contains a chemical known to the State of California to cause cancer.

SECTION 16: OTHER INFORMATION

SDS Prepared By King Packaged Materials Company
Phone No. 905-639-2993
Date of Preparation December 7, 2018

 

 

Disclaimer

To the best of our knowledge, the information contained herein is accurate. However, neither KPM Industries Ltd., nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist.


Product Calculator


How Much Do I Need?

Calculate how much of a product you need, then add it to your Shopping List.
Jump To Calculator Icon

Jump To Calculator

More Information

Apply additional 3 mm (1/8”) coats of SAKRETE ICF 5000 as needed, in order to completely cover and embed the fiberglass mesh, up to a maximum total thickness of 9 mm (3/8")*.