MasonGo 100

 

 

MasonGo 100 is a pre-mixed, pre-bagged, Type N mortar specially designed for laying bricks, natural stones, concrete blocks and other masonry products. This mortar is composed of cementitious material, an air-entraining agent and sand, with a controlled particle size distribution. MasonGo 100 mortar complies with Table 6 of CSA-A179-14 for Type N mortar with addition of water on-site. This product is grey in colour, but may be coloured in the factory or field using KING’s exclusive Colour Plus System.

• Economical
• Factory calibrated mix
• Good adhesion characteristics
• Good resistance to freeze-thaw cycles
• Pre-blended, ensuring consistency from the first batch to the last
• All KING products are manufactured using ISO 9001:2015 Certified Processes


1. FEATURES & BENEFITS

• Economical
• Factory calibrated mix
• Good adhesion characteristics
• Good resistance to freeze-thaw cycles
• Pre-blended, ensuring consistency from the first batch to the last
• All KING products are manufactured using ISO 9001:2015 Certified Processes

2. USES

Laying brick, natural stone or concrete blocks

3. EXECUTION

• The application of the mortar must comply with the requirements of Sections 6 and 7 of CSA A371-14
• Never spread mortar on frozen surfaces

4. MIXING

Mix MasonGo 100 mortar with a maximum of 4.5 L (1.2 US gallons) of potable water per
30 KG (66 lb) bag of mortar, in a clean mortar mixer. Pour 4.0 L (1.0 US gallon) of water into the blender and add 30 KG (66 lb) of MasonGo 100 mortar. Mix for 3 to 5 minutes, or 5 to 10 minutes if a colourant is added in the field. Allow the mortar to rest for a short period of time. Using the remaining water, adjust the mortar to obtain the desired consistency.

5. PLACEMENT OF MORTAR

The placement of the mortar must be done in the period of time stipulated in article 6.3.1. of CSA A179-14.

6. TOOLING OF JOINTS

The tooling of joints exposed to rain is an important step that contributes to the waterproofing of the masonry system, and must be done using a jointer. The amount of water present in the mortar joint at the time of tooling will determinate the final colour of the cured mortar. To avoid colour variation, ensure that the mortar joint always contains the same amount of water when it is tooled. As a general rule, the joint is considered ready to be tooled when the mortar has hardened sufficiently, such that the fingerprint mark remains. Unless otherwise stated, a concave joint is preferred.

7. CLEANING

Using water, a piece of jute or a piece of wood, make sure to remove as much splash or mortar stains as possible, before the mortar has hardens, to prevent the use of cleaning agents. If the use of cleaning products is necessary, be sure to contact the manufacturer of the product to validate the compatibility and the procedure to follow.

Regardless of the technique, or product selected, it is essential to preserve the integrity of the mortar.

8. CAUTION

Colour variations on the hardened mortar can be observed even if the mortar in-place has been previously coloured in the factory and complies with the project specifications.

These colour variations are mainly attributed to various implementation conditions such as delay between mixing and tooling of the joints, lack of protection against the weather during implementation, or rate of absorption/ humidity variability. In order to avoid an undesirable result, we recommend that you pay particular attention to these points.

9. TECHNICAL DATA*

REQUIREMENT OF CSA
A179-14 STANDARD
AVERAGE VALUE OF
MASONGO 100

 

MINIMUM COMPRESSIVE STRENGTH
ASTM C 109

7 days 3 MPa (435 psi) 3.5 MPa (508 psi)
28 days 5 MPa (725 psi) 6.5 MPa (943 psi)

 

FLOW

110% +/- 5% 110% +/- 5%

 

AIR CONTENT
CSA A 3004

18% Maximum 10% – 12%

 

WATER RETENTION
ASTM C 1506

70% Minimum 70%

 

VAPOUR TRANSMISSION
ASTM E 96

N/A 15 Perms

 

SHRINKAGE
ASTM C 596 – 91 Day

N/A 0.129%

 

FREEZE-THAW RESISTANCE
ASTM C 666M

N/A Excellent after 50 cycles

 

YIELD PER 30 KG (66 LB) BAG

N/A 0.018 m3 (0.65 ft3) of fresh mortar

 

*All values required by the CSA A-179-14 Standard, as well as the average values of the KING product, are obtained under laboratory conditions. The average values of the KING product are applicable when the product is used as a bedding mortar; if the product is used as a repointing or parging mortar, the average values will be different.

10. LIMITATIONS

• Do not use the MasonGo 100 when a Type S mortar is specified. In this case, it is recommended to use KING 2-1-9 or KING Block
• Never add admixtures on-site to modify set time, handling or any other property of the plastic or hardened mortar
• Use only the recommended amount of water to obtain the properties of the desired plastic or hardened mortar
• Do not use MasonGo 100 for floor applications

11. PACKAGING

This product is packaged in 30 KG (66 lb), triple-lined bags or bulk bags, wrapped on wooden pallets.

12. STORAGE AND SHELF LIFE

Always store in a dry area, protected from the weather. On-site, an additional tarpaulin must be used to cover the product to prevent water in filtration. Unopened, properly stored bags have a shelf life of 12 months.

13. SAFETY PROCEDURES

This product is made of Portland Cement. Wearing safety equipment used for the handling of cement-based products is therefore recommended: rubber gloves, dust mask and safety glasses. Safety Data Sheets can be provided upon request.

Warranty

This product is designed to meet the performance specifications outlined in this product data sheet. If the product is used in conditions for which it was not intended, or applied in a manner contrary to the written recommendations contained in the product data sheet, the product may not reach such performance specifications. The foregoing is in lieu of any other warranties, representations or conditions, expressed or implied, including, but not limited to, implied warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade.

 

 

MasonGo 100 is a pre-mixed, pre-bagged, Type N mortar specially designed for laying bricks, natural stones, concrete blocks and other masonry products. This mortar is composed of cementitious material, an air-entraining agent and sand, with a controlled particle size distribution. MasonGo 100 mortar complies with Table 6 of CSA-A179-14 for Type N mortar with addition of water on-site. This product is grey in colour, but may be coloured in the factory or field using KING’s exclusive Colour Plus System.

• Economical
• Factory calibrated mix
• Good adhesion characteristics
• Good resistance to freeze-thaw cycles
• Pre-blended, ensuring consistency from the first batch to the last
• All KING products are manufactured using ISO 9001:2015 Certified Processes


SECTION 1: GENERAL

1.1 REFERENCES

CSA Standards
.1 CSA A-179 Mortar and grout for unit masonry
.2 CSA A-371 Masonry for buildings

ASTM Standards
.1 C 207 (2011) Standard Specification for Hydrated Lime for Masonry Purposes
.2 C 270 Standard Specification for Mortar for Unit Masonry

National Building Code (Quebec)
.1 Section 9.20 (Load-bearing and Non-Load-Bearing Masonry)
.2 Sections 9.20 and 9.22 (Chimney and Fireplace)

Documents from the Institut de la Maçonnerie du Québec (IMQ)
.1 Masonry work for buildings
.2 Technical bulletins No. 7-8R
.3 Technical bulletin No. 15R

1.2 DOCUMENTS/SAMPLES/INFORMATION TO SUBMIT FOR APPROVAL

.1 Submit the required Technical Data Sheets and the samples conforming to section 01 33 00 – documents and samples to submit.

.2 Submit 3 samples of each mortar selected by the architect. The samples must be presented in the U-shaped plastic extrusions measuring 10 mm X 10 mm X 100 mm in length. The samples must be correctly identified.

.3 Submit the Technical Data Sheet of each mortar or grout used. The Technical Data Sheet must include the product’s characteristics, performance criteria and limits.

.4 Submit two copies of the Safety Data Sheet of each mortar or grout used.

.5 No requests for equivalency will be accepted after the bid closing date.

1.3 WORKABILITY AND STORAGE

.1 The mortar and grout product bags must be stored on wooden pallets and protected against inclement weather.

1.4 WALL MOCK-UP

.1 Build a wall mock-up with a minimum height and length of 1000 mm X 1000 mm.

.2 Build a wall mock-up for each mortar and grout specified.

.3 The wall mock-up should display what the final colour and texture of the joint will look like.

.4 The wall mock-up must form an integral part of the works.

.5 Do not start work until the wall mock-up has been approved by the architect.

1.5 PLACEMENT CONDITIONS

Cold Weather Placement:

When the temperature during the day ranges from:

0°C to  4°C:
The sand or mixing water must be heated to a temperature between 20°C and 70°C.

0°C to -4°C:
The sand and the mixing water must be heated to a temperature between 20 and 70 °C.

-4°C to -7°C:
1) The sand and mixing water must be heated to a temperature between 20°C and 70 °C.
2) Both sides of the walls under construction must be heated.
3) Windbreakers must be used when wind speed exceeds 25 km/h.

-7°C and lower:
1) The sand and the mixing water must be heated to a temperature between 20°C and 70°C.
2) Enclosures and supplementary heating must be planned for in order to maintain air temperature above 0 °C.
3) The temperature of the masonry unit at the time of placement cannot be less than 7°C.

Hot Weather Placement:

.1 Cover the opening with a waterproof tarpaulin to prevent it from drying too quickly. Make sure to use a tarpaulin that does not stain.

Never wet the masonry units, unless otherwise indicated by the architect.

1.6 PROTECTIVE MEASURES

.1 Unfinished masonry works must be wrapped with waterproof tarpaulins that do not stain. The tarpaulins must cover the walls and extend them by 600 mm on each side to protect the works against gusts of rain caused by wind.

.2 Finished masonry works must be protected from mortar spatter by covering them with stain-free tarpaulins or polyethylene.

.3 Protect the windows, frames, doors and sills from spatter or other damaging elements.

SECTION 2: PRODUCTS

2.1 MATERIALS

.1 Mortar and grout materials must be provided by the same supplier.

.2 All mortar and grout must be manufactured in a plant where processes are certified ISO 9001:2008.

.3 Portland Type GU Cement, conforming to standard CSA A 3000.

.4 Hydrated lime Type S, conforming to standard ASTM C 207 (2011).

.5 Sand: Fine-grain sand granulometry conforming to Table 1 of standard CSA A 179.

.6 Water: Only use clean potable water free of harmful substances such as oils, acids, salts and organic matter.

.7 Pigments: Use iron oxide pigments. The percentage of pigments should not exceed 10% of the binder density.

.8 It is strictly prohibited to use any type of additive to alter the setting time, workability or any other property of the plastic or cured mortar.

2.2 TYPES OF MORTARS

.1 All mortars described hereafter are manufactured by the company “KING PACKAGED MATERIALS COMPANY”.

.2 Each type of mortar must be factory pre-blended with Portland cement, lime, sand and colouring agents, and then mixed with water at the construction site according to the manufacturer’s instructions.

.3 Mortar for exterior masonry work, above ground level.

.1 Mortar for load-bearing walls: As a minimum, use a Type S Mortar such as KING 2-1-9,                  prepared according to the batching specifications

.2 Mortar for non-load-bearing walls: As a minimum, use a Type N Mortar like KING 1-1-6,                prepared according to the batching specifications

.4 Mortar for interior masonry works

.1 Mortar for load-bearing walls: As a minimum, use a Type S Mortar like KING Block or
KING 2-1-9.

.2 Mortars for non-load-bearing walls: As a minimum, use a Type N Mortar such as
KING 1-1-6, prepared according to the batching specifications.

2.3 TYPES OF GROUTS

.1 All grouts described hereafter are manufactured by the company “KING PACKAGED MATERIALS COMPANY”.

.2 It is strictly prohibited to use mortar as grout.

.3 Each type of grout must be factory pre-blended with the raw materials, and then mixed with water on the construction site according to the manufacturer’s instructions.

.4 The grouts must conform to Table 7 of standard CSA A 179.

.5 Grout should be an expansive type. Expansion shall be less than 2%.

.6 Unless otherwise indicated, to fill the cells of the block, use a grout with 15 MPa at 28 days, such as KING E-15.

SECTION 3: EXECUTION

3.1 MIXING

.1 Always use a clean mixer for each type of mortar and colour.

.2 Conformity: Comply with the requirements, recommendations and specifications on the manufacturer’s Technical Data Sheet.

3.2 PLACEMENT

.1 Unless otherwise indicated by the architect, place the masonry mortar and grout in compliance with standards CSA A 179 and CSA A 371.

3.3 JOINTS

.1 Unless otherwise indicated by the architect, the joints must be 10 mm thick.

.2 The joints must be smoothed so that they have a concave profile.

3.4 PLACEMENT TIMEFRAME FOR MORTAR AND GROUT

Mortar
.1 If room temperature is equal to or greater than 25°C, mortar must be placed in under 1.5 hours after mixing. If room temperature is less than 25°C, mortar must be placed in under 2.5 hours after mixing.

Grout
.1 Expansive grout must be placed at the latest 20 minutes after mixing. Regular grout must .1 Expansive grout must be placed at the latest 20 minutes after mixing. Regular grout must be placed in under 1.5 hours after mixing.

3.5 REMIXING

.1 Remixing is a criteria of placing mortar and grout. It is done to ensure the necessary workability.

3.6 COLOUR UNIFORMITY

In order to ensure colour uniformity of the mortar, the contractor must:

.1 Use the same supplier for all mortar and grout.

.2 Ensure that the quantity of water in the mortar joints remains the same while smoothing them.

.3 Always use a clean mixer.

3.7 CLEANING

Once finished the work, remove the excess mortar using a wooden blade. Once the mortar has sufficiently cured, the contractor must:

.1 Moisten the wall surface with clean water, starting from the bottom.

.2 Scour the wall surface using soapy water and a brush with nylon bristles.

.3 Do NOT use any form of acid, unless otherwise indicated by the architect.

 

Writers' Professional Liability

This document is published by KING MASONRY PRODUCTS. It contains information for the sole purpose of helping you make informed decisions. It is not our intention and we cannot assume, in anyway, the role and professional liability of the architect who executed, signed and sealed these plans and specifications.

As such, this document was diligently drafted by experienced professionals and therefore must not be copied integrally; rather, you must adapt or even modify it according to your project, which our technical representatives and engineering service representatives would be more than happy to help you with.

 

 

MasonGo 100 is a pre-mixed, pre-bagged, Type N mortar specially designed for laying bricks, natural stones, concrete blocks and other masonry products. This mortar is composed of cementitious material, an air-entraining agent and sand, with a controlled particle size distribution. MasonGo 100 mortar complies with Table 6 of CSA-A179-14 for Type N mortar with addition of water on-site. This product is grey in colour, but may be coloured in the factory or field using KING’s exclusive Colour Plus System.

• Economical
• Factory calibrated mix
• Good adhesion characteristics
• Good resistance to freeze-thaw cycles
• Pre-blended, ensuring consistency from the first batch to the last
• All KING products are manufactured using ISO 9001:2015 Certified Processes


SECTION 1: IDENTIFICATION

Product Identifier MasonGo 100
Other Means of Identification MasonGo 100
Product Family KING Masonry Products-Type N Mortars
Recommended Use Ideal for use in laying clay, concrete and stone masonry units. Can be applied indoors, outdoors or for any other masonry application where high bond strength is required.
Restrictions on Use None known.
Manufacturer King Packaged Materials Company, 3385 Harvester Road, Burlington, Ontario, L7R 3Y5, www.kpmindustries.com
Emergency Phone No. King Packaged Materials Company, (800) 461-0566, 8:30am-4:30pm
Chemtrec, (800) 424-9300, 24 hours/7 days a week
SDS No. 0119
Date of Preperation May 1, 2017

SECTION 2: HAZARD IDENTIFICATION

Classification
Skin irritation – Category 2; Serious eye damage – Category 1; Skin sensitization – Category 1; Carcinogenicity – Category 1A; Specific target organ toxicity (single exposure) – Category 3; Specific target organ toxicity (repeated exposure) – Category 1

Label Elements

Signal Word:
Danger

Hazard Statement(s):
Causes skin irritation.
Causes serious eye damage.
May cause an allergic skin reaction.
May cause cancer.
May cause respiratory irritation.
Causes damage to organs (lungs) through prolonged or repeated exposure.

Precautionary Statement(s):
Obtain special instructions before use.
Do not handle until all safety precautions have been read and understood.
Wash hands thoroughly after handling.
Contaminated work clothing must not be allowed out of the workplace.
Wear protective gloves/protective clothing/eye protection/face protection.
Use only outdoors or in a well-ventilated area.
Do not breathe dust/fume/gas/mist/vapours/spray.
Do not eat, drink or smoke when using this product.

IF exposed or concerned: Get medical advice/attention.
IF ON SKIN: Wash with plenty of water.
Take off contaminated clothing and wash it before reuse.
If skin irritation or rash occurs: Get medical advice/attention.
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTRE or doctor.
IF INHALED: Remove person to fresh air and keep comfortable for breathing.
Call a POISON CENTRE or doctor if you feel unwell.

Store locked up.
Store in a well-ventilated place. Keep container tightly closed.
Dispose of contents and container in accordance with local, regional, national and international regulations.
10% of the mixture consists of ingredient(s) of unknown acute toxicity.

Other Hazards
None known.

SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS

Mixture:

Chemical Name CAS Registry No. Concentration % Other Identifiers
Silica, total quartz 14808-60-7 60-100% Not applicable
Portland Cement 65997-15-1 10-30% Not applicable

 

Notes
The exact percentage (concentration) of composition has been withheld as a trade secret in accordance with paragraph (i) of §1910.1200.

SECTION 4: FIRST-AID MEASURES

First-Aid Measures

Inhalation
Move to fresh air. Keep at rest in a position comfortable for breathing. Call a Poison Centre or doctor if you feel unwell.
Skin Contact
Rinse with lukewarm, gently flowing water for 5 minutes. Take off immediately contaminated clothing, shoes and leather goods (e.g. watchbands, belts). Thoroughly clean clothing, shoes and leather goods before reuse or dispose of safely. If skin irritation or a rash occurs, get medical advice or attention.
Eye Contact
Immediately rinse the contaminated eye(s) with lukewarm, gently flowing water for 15-20 minutes, while holding the eyelid(s) open. Remove contact lenses, if present and easy to do. Immediately call a Poison Centre or doctor.
Ingestion
Never give anything by mouth if person is rapidly losing consciousness, or is unconscious or convulsing. Do not induce vomiting. Get medical advice or attention if you feel unwell or are concerned.

Most Important Symptoms and Effects, Acute and Delayed
If inhaled: can irritate the nose and throat. Can cause lung injury. If on skin: skin sensitizer. May cause an allergic skin reaction in some people. May cause moderate to severe irritation. If in eyes: causes moderate to severe irritation. Symptoms include sore, red eyes, and tearing. If swallowed: can irritate the mouth, throat and stomach. Symptoms may include nausea, vomiting, stomach cramps and diarrhea.

Immediate Medical Attention and Special Treatment

Special Instructions
Not applicable.

SECTION 5: FIRE-FIGHTING MEASURES

Extinguishing Media

Suitable Extinguishing Media
Not combustible. Use extinguishing agent suitable for surrounding fire.
Unsuitable Extinguishing Media
None known.

Specific Hazards Arising from the Product
This product presents no unusual hazards in a fire situation.

Special Protective Equipment and Precautions for Fire-fighters
Approach fire from upwind to avoid hazardous vapours or gases. Fire-fighters may enter the area if positive pressure SCBA and full Bunker Gear is worn.

SECTION 6: ACCIDENTAL RELEASE MEASURES

Personal Precautions, Protective Equipment, and Emergency Procedures
Use the personal protective equipment recommended in Section 8 of this safety data sheet. Evacuate the area immediately. Isolate the hazard area. Keep out unnecessary and unprotected personnel.

Environmental Precautions
It is good practice to prevent releases into the environment. Do not allow into any sewer, on the ground or into any waterway.

Methods and Materials for Containment and Cleaning Up
Collect using shovel/scoop or approved HEPA vacuum and place in a suitable container for disposal. Avoid generating dust.

SECTION 7: HANDLING AND STORAGE

Precautions for Safe Handling
Avoid repeated or prolonged skin contact. Do not swallow. Do not breathe in this product. Avoid generating dusts. Keep containers tightly closed when not in use or empty. Do NOT eat, drink or store food in work areas.

Conditions for Safe Storage
Store in the original, labelled, shipping container. Store in an area that is: dry, well-ventilated. Protect product from contact with water, including humidity. Prevent rainwater and ground water from reaching storage area.

SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION

Control Parameters

ACGIH TLV®

OSHA PEL

AIHA WEEL

Chemical Name

TWA

STEL

TWA

Ceiling

8-hr TWA

TWA

Silica, total quartz

0.05 mg/m3
(R) A2

0.1 mg/m3

Portland cement

1 mg/m3
(R) A4

5 mg/m3
(R)

 

Appropriate Engineering Controls
Use local exhaust ventilation, if general ventilation is not adequate to control amount in the air.

Individual Protection Measures

Eye/Face Protection
Wear chemical safety goggles and face shield when contact is possible.
Skin Protection
Wear chemical protective clothing e.g. gloves, aprons, boots.
Respiratory Protection
Wear a NIOSH approved particulate respirator equipped with an N95, R95, or P95 filter.

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

Basic Physical and Chemical Properties

Appearance Grey powder
Odour Odourless
Odour Threshold Not available
pH Not available
Melting Point/Freezing Point Not available (melting); Not available (freezing)
Initial Boiling Point/Range Not available
Flash Point Not available
Evapouration Rate Not available
Flammability (solid, gas) Not applicable
Upper/Lower Flammability or Explosive Limit Not available (upper); Not available (lower)
Vapour Pressure Not available
Vapour Density (air = 1) Not available
Relative Density (water = 1) 2.5
Solubility Not available (in water); Not available (in other liquids)
Partition Coefficient, n-Octanol/Water (Log Kow) Not available
Auto-Ignition Temperature Not available
Decomposition Temperature Not available
Viscosity Not available (kinematic); Not available (dynamic)
Physical State Solid

SECTION 10: STABILITY AND REACTIVITY

Reactivity
Not reactive under normal conditions of use.

Chemical Stability
Normally stable.

Possibility of Hazardous Reactions
None expected under normal conditions of storage and use.

Conditions to Avoid
Water, moisture or humidity.

Incompatible Materials
None known.

Hazardous Decomposition Products
Under normal conditions of storage and use, hazardous decomposition products should not be produced.

SECTION 11: TOXICOLOGICAL INFORMATION

Likely Routes of Exposure
Inhalation; skin contact; eye contact; ingestion.

Acute Toxicity

Chemical Name LC50 LD50 (oral) LD50 (dermal)
Silica, total quartz 500 mg/kg (rat)

 

Skin Corrosion/Irritation
May cause moderate or severe irritation based on information for closely related materials.
Serious Eye Damage/Irritation
May cause serious eye damage based on information for closely related materials.

STOT (Specific Target Organ Toxicity) – Single Exposure

Inhalation
May cause severe nose and throat irritation, severe lung injury.
Skin Absorption
No information was located.
Ingestion
May be harmful based on information for closely related materials.

Aspiration Hazard
Can cause lung damage if aspirated based on human experience.

STOT (Specific Target Organ Toxicity) – Repeated Exposure
Causes irritation of the respiratory system. Respiratory tract injury has been observed. Respirable crystalline silica in the form of quartz or cristobalite from occupational sources is listed by the International Agency for Research on Cancer (IARC) and National Toxicology Program (NTP) as a lung carcinogen. Prolonged exposure to respirable crystalline silica has been known to cause silicosis, a lung disease, which may be disabling. While there may be a factor of individual susceptibility to a given exposure to respirable silica dust, the risk of contracting silicosis and the severity of the disease is clearly related to the amount of dust exposure and the length of time (usually years) of exposure.

Respiratory and/or Skin Sensitization
May cause an allergic reaction (skin sensitization) based on information for closely related chemicals.

Carcinogenicity

Chemical Name IARC ACGIH® NTP OSHA
Silica, total quartz Group 1 A1 Known carcinogen

 

May cause cancer.

Reproductive Toxicity

Development of Offspring
No information was located.
Sexual Function and Fertility
No information was located.
Effects on or via Lactation
No information was located.

Germ Cell Mutagenicity
No information was located.
Interactive Effects
No information was located.

SECTION 12: ECOLOGICAL INFORMATION

Ecotoxicity
May cause long lasting harmful effects to aquatic life.

Persistence and Degradability
No information was located.

Bioaccumulative Potential
No information was located.

Mobility in Soil
No information was located.

Other Adverse Effects
There is no information available.

SECTION 13: DISPOSAL CONSIDERATIONS

Disposal Methods
Contact local environmental authorities for approved disposal or recycling methods in your jurisdiction.

SECTION 14: TRANSPORT INFORMATION

Not regulated under US DOT Regulations.

Environmental Hazards
Not applicable
Special Precautions
Not applicable

Transport in Bulk According to Annex II of MARPOL 73/78 and the IBC Code
Not applicable

SECTION 15: REGULATORY INFORMATION

Safety, Health and Environmental Regulations
Canada

WHMIS Classification

Class D2A, Class E
D2A – Very Toxic (Chronic toxicity; Carcinogenicity); E – Corrosive

This product has been classified in accordance with the hazard criteria of the Controlled Products Regulations and the SDS contains all of the information required by the Controlled Products Regulations.

USA

Toxic Substances Control Act (TSCA) Section 8(b)
All ingredients are on the TSCA Inventory or are exempt from TSCA Inventory requirements under 40 CFR 720.
Additional USA Regulatory Lists
This product contains a chemical known to the State of California to cause cancer.

SECTION 16: OTHER INFORMATION

SDS Prepared By King Packaged Materials Company
Phone No. 905-639-2993
Date of Preparation May 1, 2017

 

Disclaimer

To the best of our knowledge, the information contained herein is accurate. However, neither KPM Industries Ltd., nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist.


More Information

The KING Masonry Products group offers a variety of specification documents. E-mail masonry@kpmindustries.com to request these resources for King Masonry Products.