KingAnchor



KingAnchor is a neat, high performance, shrinkage compensated, anchoring grout. It is an unsanded, Portland cement-based, expanding, shrinkage-compensated, anchoring grout containing various additives allowing controlled expansion in both plastic and hardened states. KingAnchor is ideal for anchoring cables, tendons or bolts in rock or soil media.

• Superior early strength gain allowing early tensioning of anchors
• Excellent pumpability
• Excellent cohesion and plastic stability
• Thixotropic properties reduce material loss in fractured ground
• Non-corrosive, non-chloride, non-metallic
• Reduced bleeding


1. FEATURES & BENEFITS

• Superior early strength gain allowing early tensioning of anchors
• Excellent pumpability
• Excellent cohesion and plastic stability
• Thixotropic properties reduce material loss in fractured ground
• Non-corrosive, non-chloride, non-metallic
• Reduced bleeding
• All KING products are manufactured using ISO 9001:2015 Certified Processes

2. USES

• For most grouted anchor requirements including cable bolting, earth tie-backs for excavation or soil stabilization, grouting anchors in tunnel support systems, re-bar grouting, and grouting soil or rock tendons for anchoring piles or foundation structures.
• Contact your KING Technical Representative for recommendations or information on uses or conditions not listed above.

3. PROCEDURES

Mixing: For a 30 KG (66 lb) bag, the recommended volume of water is 9.0 L (2.38 US gallons). Use potable water only. Introduce potable water into a high shear mixer and then add KingAnchor while operating at medium speed. Increase mixer speed and continue mixing at high speed for 2 to 3 minutes. Mortar-style mixers are not recommended for this purpose. Decrease mixer speed to low and continue mixing while placing the grout. The time between mixing and pumping of the batch should not exceed 30 minutes.

4. TECHNICAL DATA

The following data is representative of typical values achievable under laboratory conditions. Results in the field may vary.

MASS DENSITY

ASTM C 109 2000 kg/m3 (125 lb/ft3)

 

FLOW

ASTM C 939 15-30 seconds

 

COMPRESSIVE STRENGTH

ASTM C 109
1 Day 25 MPa (3625 psi)
3 Day 45 MPa (6500 psi)
7 Day 50 MPa (7250 psi)
28 Day 60 MPa (8700 psi)

 

EXPANSION

ASTM C 940 ≤ 2.0%

 

BLEEDING

ASTM C 940 Nil

 

SEGREGATION

  Nil

 

HARDENED HEIGHT CHANGE

ASTM C 1090
1 Day 0.0%-0.2%
3 Day 0.0%-0.2%
7 Day 0.0%-0.2%
28 Day 0.0%-0.2%

5. OPTIMUM PERFORMANCE

Not recommended for areas subjected to extremely high vibrations. Adhere to recommended water additions. Exceeding the recommended water:material ratio will result in reduced compressive strengths and inferior physical properties.

6. YIELD

30 KG (66 lb) bag contains approximately 19.5 L (0.69 ft3) of fluid grout.

7. PACKAGING

KingAnchor is normally packaged in 30 KG (66 lb) triple-lined bags and polywrapped on wooden pallets. All KING products can be custom packaged to suit specific job requirements

8. STORAGE AND SHELF LIFE

Material should be stored in a dry, covered area, protected from the elements. Unopened pails have a shelf life of 12 months.

9. SAFETY PROCEDURES

KingAnchor contains Portland cement. Normal safety-wear such as rubber gloves, dust mask and safety glasses used to handle conventional cement based products should be worn. Safety Data Sheets are available upon request.

Warranty

This product is designed to meet the performance specifications outlined in this product data sheet. If the product is used in conditions for which it was not intended, or applied in a manner contrary to the written recommendations contained in the product data sheet, the product may not reach such performance specifications. The foregoing is in lieu of any other warranties, representations or conditions, expressed or implied, including, but not limited to, implied warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade.



KingAnchor is a neat, high performance, shrinkage compensated, anchoring grout. It is an unsanded, Portland cement-based, expanding, shrinkage-compensated, anchoring grout containing various additives allowing controlled expansion in both plastic and hardened states. KingAnchor is ideal for anchoring cables, tendons or bolts in rock or soil media.

• Superior early strength gain allowing early tensioning of anchors
• Excellent pumpability
• Excellent cohesion and plastic stability
• Thixotropic properties reduce material loss in fractured ground
• Non-corrosive, non-chloride, non-metallic
• Reduced bleeding


SECTION 1: IDENTIFICATION

Product Identifier

KingAnchor

Other Means of Identification

KingAnchor

Product Family

KING Construction Products – Grout

Recommended Use

For most grouted anchor requirements including, cable bolting, earth tie backs for excavation or soil stabilization, grouting anchors in tunnel support systems, re-bar grouting and grouting soil or rock tendons for anchoring piles or foundation structures.

Restrictions on Use

None known.

Manufacturer

King Packaged Materials Company, 555 Michigan Drive, Suite 100, Oakville, Ontario, L6L 0G4, www.kpmindustries.com

Emergency Phone No.

King Packaged Materials Company, (800) 461-0566, 8:30am-4:30pm, Chemtrec, (800) 424-9300, 24 hours/7 days a week

SDS No.

0476

Date of Preparation

March 15, 2019

SECTION 2: HAZARD IDENTIFICATION

Classification
Skin irritation – Category 2; Serious eye damage – Category 1; Skin sensitization – Category 1; Carcinogenicity – Category 1A; Specific target organ toxicity (single exposure) – Category 3; Specific target organ toxicity (repeated exposure) – Category 1

Label Elements

Signal Word:
Danger

Hazard Statement(s):
Causes skin irritation.
Causes serious eye damage.
May cause an allergic skin reaction.
May cause cancer.
May cause respiratory irritation.
Causes damage to organs (lungs) through prolonged or repeated exposure.

Precautionary Statement(s):
Obtain special instructions before use.
Do not handle until all safety precautions have been read and understood.
Wash hands thoroughly after handling.
Contaminated work clothing must not be allowed out of the workplace.
Wear protective gloves/protective clothing/eye protection/face protection.
Use only outdoors or in a well-ventilated area.
Do not breathe dust/fume/gas/mist/vapours/spray.
Do not eat, drink or smoke when using this product.

IF exposed or concerned: Get medical advice/attention.
IF ON SKIN: Wash with plenty of water.
Take off contaminated clothing and wash it before reuse.
If skin irritation or rash occurs: Get medical advice/attention.
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTRE or doctor.
IF INHALED: Remove person to fresh air and keep comfortable for breathing.

Call a POISON CENTRE or doctor if you feel unwell.
Store locked up.
Store in a well-ventilated place. Keep container tightly closed.
Dispose of contents and container in accordance with local, regional, national and international regulations.
60% of the mixture consists of ingredient(s) of unknown acute toxicity.

Other Hazards
None known.

SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS

Mixture:

Chemical Name CAS No. % Other Identifiers
Portland Cement 65997-15-1 60-100% Not applicable
Fly Ash 68131-74-8 10-30% Not applicable
Silica, total quartz 14808-60-7 0.1-1% Not applicable

 

Notes:The exact percentage (concentration) of composition has been withheld as a trade secret in accordance with paragraph (i) of §1910.1200.

SECTION 4: FIRST-AID MEASURES

First-Aid Measures

Inhalation
Move to fresh air. Keep at rest in a position comfortable for breathing. Call a Poison Centre or doctor if you feel unwell.
Skin Contact
Rinse with lukewarm, gently flowing water for 5 minutes. Take off immediately contaminated clothing, shoes and leather goods (e.g. watchbands, belts). Thoroughly clean clothing, shoes and leather goods before reuse or dispose of safely. If skin irritation or a rash occurs, get medical advice or attention.
Eye Contact
Immediately rinse the contaminated eye(s) with lukewarm, gently flowing water for 15-20 minutes, while holding the eyelid(s) open. Remove contact lenses, if present and easy to do. Immediately call a Poison Centre or doctor.
Ingestion
Never give anything by mouth if person is rapidly losing consciousness, or is unconscious or convulsing. Do not induce vomiting. Get medical advice or attention if you feel unwell or are concerned.

Most Important Symptoms and Effects, Acute and Delayed
If inhaled: can irritate the nose and throat. Can cause lung injury. If on skin: skin sensitizer. May cause an allergic skin reaction in some people. May cause moderate to severe irritation. If in eyes: causes moderate to severe irritation. Symptoms include sore, red eyes, and tearing. If swallowed: can irritate the mouth, throat and stomach. Symptoms may include nausea, vomiting, stomach cramps and diarrhea.

Immediate Medical Attention and Special Treatment

Special Instructions
Not applicable.

SECTION 5: FIRE-FIGHTING MEASURES

Extinguishing Media

Suitable Extinguishing Media
Not combustible. Use extinguishing agent suitable for surrounding fire.
Unsuitable Extinguishing Media
None known.

Specific Hazards Arising from the Product
This product presents no unusual hazards in a fire situation.

Special Protective Equipment and Precautions for Fire-Fighters
Approach fire from upwind to avoid hazardous vapours or gases. Fire-fighters may enter the area if positive pressure SCBA and full Bunker Gear is worn.

SECTION 6: ACCIDENTAL RELEASE MEASURES

Personal Precautions, Protective Equipment, and Emergency Procedures
Use the personal protective equipment recommended in Section 8 of this safety data sheet. Evacuate the area immediately. Isolate the hazard area. Keep out unnecessary and unprotected personnel.

Environmental Precautions
It is good practice to prevent releases into the environment. Do not allow into any sewer, on the ground or into any waterway.

Methods and Materials for Containment and Cleaning Up
Collect using shovel/scoop or approved HEPA vacuum and place in a suitable container for disposal. Avoid generating dust.

SECTION 7: HANDLING AND STORAGE

Precautions for Safe Handling
Avoid repeated or prolonged skin contact. Do not swallow. Do not breathe in this product. Avoid generating dusts. Keep containers tightly closed when not in use or empty. Do NOT eat, drink or store food in work areas.

Conditions for Safe Storage
Store in the original, labelled, shipping container. Store in an area that is: dry, well-ventilated. Protect product from contact with water, including humidity. Prevent rainwater and ground water from reaching storage area.

SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION

Control Parameters

ACGIH TLV®

OSHA PEL

AIHA WEEL

Chemical Name

TWA

STEL

TWA

Ceiling

8-hr TWA

TWA

Portland cment

1 mg/m3
(R) A4

5 mg/m3
(R)
Silica, total quartz

0.05 mg/m3
(R) A2

0.1 mg/m3

Fly Ash

80 mg/m3
(R)

 

Appropriate Engineering Controls
Use local exhaust ventilation, if general ventilation is not adequate to control amount in the air.

Individual Protection Measures

Eye/Face Protection
Wear chemical safety goggles and face shield when contact is possible.
Skin Protection
Wear chemical protective clothing e.g. gloves, aprons, boots.
Respiratory Protection
Wear a NIOSH approved particulate respirator equipped with an N95, R95, or P95 filter.

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

Basic Physical and Chemical Properties

Appearance Grey powder
Odour

Odourless

Odour Threshold

Not available

pH

Not available

Melting Point/Freezing Point Not available (melting); Not available (freezing)

Initial Boiling Point/Range

Not available

Flash Point

Not available

Evapouration Point

Not available

Flammability (solid, gas)

Not applicable

Upper/Lower Flammability or Explosive Limit

Not available (upper); Not available (lower)

Vapour Pressure

Not available

Vapour Density (air = 1)

Not available

Relative Density (water = 1)

2.5

Solubility

Not available (water); Not available (other liquids)

Partition Coefficient, n-Octanol/Water (Log Kow)

Not available

Auto-ignition Temperature

Not available

Decomposition Temperature

Not available

Viscosity

Not available (kinematic); Not available (dynamic)

Physical State

Solid

SECTION 10: STABILITY AND REACTIVITY

Reactivity
Not reactive under normal conditions of use.

Chemical Stability
Normally stable.

Possibility of Hazardous Reactions
None expected under normal conditions of storage and use.

Conditions to Avoid
Water, moisture or humidity.

Incompatible Materials
None known.

Hazardous Decomposition Products
Under normal conditions of storage and use, hazardous decomposition products should not be produced.

SECTION 11: TOXICOLOGICAL INFORMATION

Likely Routes of Exposure
Inhalation; skin contact; eye contact; ingestion.

Acute Toxicity

Chemical Name LC50 LD50 (oral) LD50 (dermal)
Silica, total quartz 500 mg/kg (rat)

 

Skin Corrosion/Irritation
May cause moderate or severe irritation based on information for closely related materials.
Serious Eye Damage/Irritation
May cause serious eye damage based on information for closely related materials.

STOT (Specific Target Organ Toxicity) – Single Exposure

Inhalation
May cause severe nose and throat irritation, severe lung injury.
Skin Absorption
No information was located.
Ingestion
May be harmful based on information for closely related materials.

Aspiration Hazard
Can cause lung damage if aspirated based on human experience.

STOT (Specific Target Organ Toxicity) – Repeated Exposure
Causes irritation of the respiratory system. Respiratory tract injury has been observed. Respirable crystalline silica in the form of quartz or cristobalite from occupational sources is listed by the International Agency for Research on Cancer (IARC) and National Toxicology Program (NTP) as a lung carcinogen. Prolonged exposure to respirable crystalline silica has been known to cause silicosis, a lung disease, which may be disabling. While there may be a factor of individual susceptibility to a given exposure to respirable silica dust, the risk of contracting silicosis and the severity of the disease is clearly related to the amount of dust exposure and the length of time (usually years) of exposure.

Respiratory and/or Skin Sensitization
May cause an allergic reaction (skin sensitization) based on information for closely related chemicals.

Carcinogenicity

Chemical Name IARC ACGIH® NTP OSHA
Silica, total quartz Group 1 A2 Known carcinogen

 

May cause cancer.

Reproductive Toxicity

Development of Offspring
No information was located.
Sexual Function and Fertility
No information was located.
Effects on or via Lactation
No information was located.

Germ Cell Mutagenicity
No information was located.
Interactive Effects
No information was located.

SECTION 12: ECOLOGICAL INFORMATION

Ecotoxicity
May cause long lasting harmful effects to aquatic life.

Persistence and Degradability
No information was located.

Bioaccumulative Potential
No information was located.

Mobility in Soil
No information was located.

Other Adverse Effects
There is no information available.

SECTION 13: DISPOSAL CONSIDERATIONS

Disposal Methods
Contact local environmental authorities for approved disposal or recycling methods in your jurisdiction.

SECTION 14: TRANSPORT INFORMATION

Not regulated under US DOT Regulations.

Environmental Hazards
Not applicable
Special Precautions
Not applicable

Transport in Bulk According to Annex II of MARPOL 73/78 and the IBC Code
Not applicable

SECTION 15: REGULATORY INFORMATION

Safety, Health and Environmental Regulations

Canada
This product has been classified in accordance with the hazard criteria of the Controlled Products Regulations and the SDS contains all of the information required by the Controlled Products Regulations.

USA
Toxic Substances Control Act (TSCA) Section 8(b)
All ingredients are on the TSCA Inventory or are exempt from TSCA Inventory requirements under 40 CFR 720.
Additional USA Regulatory Lists
This product contains a chemical known to the State of California to cause cancer.

SECTION 16: OTHER INFORMATION

SDS Prepared By King Packaged Materials Company
Phone No. 905-639-2993
Date of Preparation March 15, 2019

Disclaimer

To the best of our knowledge, the information contained herein is accurate. However, neither KPM Industries Ltd., nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist.