SAKRETE Concrete Adhesive

Bond a variety of materials to existing concrete! Use SAKRETE Concrete Adhesive to bond newly repaired surfaces and existing concrete or masonry surfaces. Available in 946 mL and 3.78 L containers. Go with SAKRETE, The Pro’s Choice since 1936.

Product Codes:
946 mL: 12212001
3.78 L: 12212004

• High quality, high performance, latex, bonding agent
• Ideal for bonding new and existing materials together
• Brush on to existing surfaces or mix into fresh material
• Easy to use


1. FEATURES & BENEFITS

• Bonds concrete to concrete
• Brush on or mix in
• Increases performance

2. USES

Can be used for patch repairs or resurfacing on concrete bridges, parking decks, industrial floors, retaining walls, sidewalks, parge coating foundation walls and leveling concrete floors to receive over-layments. This product can be used on wood substrate, solely for use with SAKRETE Self Leveling Underlayment. 

3. PROCEDURES

Mix and substrate temperatures should be maintained between 5 ºC and 30 ºC (40 ºF and 86 ºF) for at least 24 hours prior to and 48 hours after. Not recommended to be used in areas where in-service temperatures exceed 37 °C (100 °F).

Surface Preparation: The surface to be repaired must be structurally sound and clean, free from any dirt, oil, grease, paint or other contaminant. Use either mechanical means (such as sandblasting, wire brush) or chemical means (such as a 10% trisodium phosphate solution) to thoroughly clean the area before repair. Smooth surfaces should be roughened by mechanical means or a 10% muriatic acid solution. NOTE: acid solution must be washed off the surface thoroughly with water. Clean the area to be repaired with potable water, leaving the concrete saturated but free of standing water. Some very porous concretes may require several applications of water to ensure complete saturation.

Mixing:
Use as a Bond Coat:
Apply SAKRETE Concrete Adhesive with a paint brush or roller. Coat the entire surface evenly, leaving no puddles. Apply the prepared patching material while the bond coat is still tacky.

Mixing:
Use in the Repair Mix:
Substitute SAKRETE Concrete Adhesive in place of water when mixing SAKRETE Concrete Mix, SAKRETE Sand Mix or SAKRETE Mortar Mix. Do not dilute the SAKRETE Concrete Adhesive before adding it to the mix. To obtain the desired consistency it may be necessary to add a slight amount of water. Add only a little at a time. NOTE: When working with concretes containing air entrained agents (i.e. SAKRETE PSI 6000) use only as a bond coat.

Placing: Use a trowel and force the mix well into all voids in the prepared surface. Finish trowelling should be done right away. Do not over trowel.

4. CURING

When used in the repair mix prevent rapid drying. During hot weather or low humidity, cover the repair and protect from direct sunlight for 24 hours. For the next three days moisten the surface occasionally with a fi ne spray of water. Under normal conditions, repaired areas may be used for light traffic after 24 hours and heavy traffic after 48 hours. When used as a bond coat, follow the concrete product’s curing recommendations.

5. PAINTING

Adhesive must be fully cured (approximately 28 days) and dry before painting. Refer to paint manufacturer directions for application instructions.

6. YIELD

As a bond coat, 946 mL will cover approximately 5 m2 (50 ft2), depending upon surface porosity and condition.

As a bond coat, 3.78 L will cover approximately 20 m2 (200 ft2), depending upon surface porosity and condition.

7. SAFETY PROCEDURES

Avoid contact with eyes and skin.

FIRST AID TREATMENT: In case of contact with eyes or skin, rinse thoroughly with water. If swallowed, drink 2 glasses of water. Call physician.

Warranty

This product is designed to meet the performance specifications outlined in this product data sheet. If the product is used in conditions for which it was not intended, or applied in a manner contrary to the written recommendations contained in the product data sheet, the product may not reach such performance specifications. The foregoing is in lieu of any other warranties, representations or conditions, expressed or implied, including, but not limited to, implied warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade.

Bond a variety of materials to existing concrete! Use SAKRETE Concrete Adhesive to bond newly repaired surfaces and existing concrete or masonry surfaces. Available in 946 mL and 3.78 L containers. Go with SAKRETE, The Pro’s Choice since 1936.

Product Codes:
946 mL: 12212001
3.78 L: 12212004

• High quality, high performance, latex, bonding agent
• Ideal for bonding new and existing materials together
• Brush on to existing surfaces or mix into fresh material
• Easy to use


SECTION 1: IDENTIFICATION

Product Identifier

SAKRETE Concrete Adhesive

Other Means of Identification SAKRETE Concrete Adhesive
Product Family

KING Home Improvement Products

Recommended Use

Can be used for patch repairs or resurfacing on concrete bridges, parking decks, industrial floors, retaining walls, sidewalks, parge coating foundation walls and leveling concrete floors to receive overlayments.

Manufacturer/Supplier

King Packaged Materials Company, 3385 Harvester Road, Burlington, Ontario, L7R 3Y5, www.kpmindustries.com

Emergency Phone No. King Packaged Materials Company, (800) 461-0566, 8:30am-4:30pm
SDS No. 

0159

Date of Preparation September 30, 2016

SECTION 2: HAZARD IDENTIFICATION

Classification
Not classified under any hazard class.

Label Elements
Not applicable

SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS

Contains no hazardous ingredients.

SECTION 4: FIRST-AID MEASURES

First-Aid Measures

Skin Contact
Immediately rinse with lukewarm, gently flowing water for 15-20 minutes.
Eye Contact
Immediately rinse the contaminated eye(s) with lukewarm, gently flowing water for 15-20 minutes, while holding the eyelid(s) open.
Ingestion
Never give anything by mouth if person is rapidly losing consciousness, or is unconscious or convulsing. Do not induce vomiting. Immediately call a Poison Centre or doctor.

SECTION 5: FIRE-FIGHTING MEASURES

Extinguishing Media

Suitable Extinguishing Media
Not combustible. Use extinguishing agent suitable for surrounding fire.
Unsuitable Extinguishing Media
Non known.

Specific Hazards Arising from the Product
Does not burn.

SECTION 6: ACCIDENTAL RELEASE MEASURES

Personal Precautions, Protective Equipment, and Emergency Procedures
Avoid inhalation of the product and contact with skin. Use the personal protective equipment recommended in Section 8 of this safety data sheet.

Environmental Precautions
Do not allow into any sewer, on the ground or into any waterway.

Methods and Materials for Containment and Cleaning Up
Contain and soak up spill with absorbent that does not react with spilled product. Place used absorbent into suitable, covered, labelled containers for disposal.

SECTION 7: HANDLING AND STORAGE

Precautions for Safe Handling
Always use good industrial hygiene practices and safety guidelines.

Conditions for Safe Storage
Keep away from food and drinking water. Store in the original, labelled, shipping container. Keep containers tightly closed when not in use. Protect from freezing.

SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION

Control Parameters
Not available.

Appropriate Engineering Controls
If user operations generate dust, fume, or mist, use ventilation to keep exposure to airborne contaminants below the exposure limit.

Individual Protection Measures

Eye/Face Protection
Approved safety eye wear should be worn, based on the risk assessments performed.
Skin Protection
Personal protective equipment for the body should be selected based on the task being performed. This includes gloves, coveralls and footwear.
Respiratory Protection
Use of an approved respirator, based on a risk assessment is necessary. Respiratory protection should be selected based on the known or anticipated levels of exposure, and the work being performed.

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

Basic Physical and Chemical Properties

Appearance Milky white
Odour Sweet
Odour Threshold

Not available

pH 5-6
Melting Point/Freezing Point

0 ºC (melting); 0 ºC (freezing)

Initial Boiling Point/Range

100 ºC

Flash Point

Not applicable

Evapouration Rate

Not applicable

Upper/Lower Flammability or Explosive Limit

Not applicable (upper); Not applicable (lower)

Vapour Pressure

Not applicable

Vapour Density (air = 1)

Not applicable

Relative Density (water = 1)

1.1

Solubility

Not available (in water)

Partition Coefficient, n-Octanol/Water (Log Kow)

Not applicable

Auto-ignition Temperature

Not appilcable

Physical State Liquid

SECTION 10: STABILITY AND REACTIVITY

Chemical Stability
Normally stable.

Possibility of Hazardous Reactions
None known

Conditions to Avoid
None known.

Incompatible Materials
None known.

Hazardous Decomposition Products
Under normal conditions of storage and use, hazardous decomposition products should not be produced.

SECTION 11: TOXICOLOGICAL INFORMATION

Likely Routes of Exposure
Inhalation; skin contact; eye contact; ingestion.

Acute Toxicity
LC50: No information was located.
LD50 (oral): No information was located.
LD50 (dermal): No information was located.

No information was located for: LC50, LD50 (oral), LD50 (dermal), Skin Corrosion/Irritation, Serious Eye Damage/Irritation, STOT (Specific Target Organ Toxicity) – Single Exposure, Aspiration Hazard, STOT (Specific Target Organ Toxicity) – Repeated Exposure, Respiratory and/or Skin Sensitization, Carcinogenicity, Development of Offspring, Sexual Function and Fertility, Effects on or via Lactation, Germ Cell Mutagenicity, Interactive Effects

SECTION 12: ECOLOGICAL INFORMATION

There are no known significant effects or critical hazards.

SECTION 13: DISPOSAL CONSIDERATIONS

Disposal Methods
The generation of waste should be avoided or minimized wherever possible. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers.

SECTION 14: TRANSPORT INFORMATION

Not regulated under Canadian TDG Regulations. Not regulated under US DOT Regulations.

Special Precautions
Not applicable

Transport in Bulk According to Annex II of MARPOL 73/78 and the IBC Code
Not applicable

SECTION 15: REGULATORY INFORMATION

Safety, Health and Environmental Regulations
Canada

WHMIS 1988 Classification
Not a WHMIS controlled product

SECTION 16: OTHER INFORMATION

SDS Prepared By King Packaged Materials Company
Phone No. 905-639-2993
Date of Preparation September 30, 2016

 

Disclaimer

To the best of our knowledge, the information contained herein is accurate. However, neither KPM Industries Ltd., nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist.


Product Calculator


How Much Do I Need?

Calculate how much of a product you need, then add it to your Shopping List.
Jump To Calculator Icon

Jump To Calculator


How-To Video

More Information

PLEASE NOTE: This product was previously known as KING Concrete Adhesive.

SAKRETE Concrete Adhesive can be used to patch, repair or resurface concrete. To learn more about product applications, reference the Uses section of the Technical Data Sheet.