SAKRETE Concrete & Mortar Repair

Easily fill cracks and voids in concrete or mortar joints! Use SAKRETE Concrete & Mortar Repair, a siliconized, acrylic-latex, repair product. Available in 300 mL tubes. Go with SAKRETE, The Pro’s Choice since 1936.

Product Code: 12021118

• High quality, repair product for flexible and durable crack-filling
• Ideal for filling cracks in walks, drives, foundations and mortar joints
• Fill vertical and horizontal surfaces
• Weather-resistant after curing and protects against freeze-thaw cycling
• Fills cracks with thicknesses between 1/8″ (3.2 mm) and 3/8″ (10 mm)
• Ready to use and fast-drying


1. FEATURES & BENEFITS

• For vertical and horizontal surfaces
• Protects against damaging freeze-thaw cycles
• Flexible and durable
• Ready to use
• Fast drying

2. PROCEDURES

READ ALL DIRECTIONS BEFORE STARTING WORK.

ATTENTION: WEAR GLOVES, SAFETY GLASSES and PROTECTIVE CLOTHING!

PROCEDURES

Surface and sealant must be above 10°C (50°F) and remain so for 48-72 hours for proper curing. Temperature and relative humidity will affect curing time.

Surface Preparation: Clean all surfaces before application. Cleaned surfaces may be moist. Cracks or joints should be approximately 1/8″ (3.2 mm) to 3/8″ (10 mm) in width. Fill deep cracks with backer-rod to within 3/8” (10 mm) of surface. Very small cracks should be slightly widened to permit penetration of caulking.

Application: Cut tube nozzle to desired bead width and squeeze caulking material into crack using standard caulking gun. Smooth and trim off excess with moist putty knife or jointing tool while material is fresh.

3. CURING

Allow to air-cure for 48-72 hours prior to traffic.

4. CLEAN UP

Cleans up with water prior to drying.

5. YIELD

300 mL (10.3 oz) tube fills a space approximately:
6 mm (1/4″) x 6 mm (1/4″) x 7.6 m (25′).

6. STORAGE & SHELF LIFE

Protect from freezing. Store between 1.7 °C (35 °F) and 37.7 °C (100 °F). Unopened containor has a shelf life of 12 months.

7. SAFETY PROCEDURES

Do not swallow. Do not get in eyes or on skin.

KEEP OUT OF REACH OF CHILDREN.

FIRST AID: Contact with eyes: Flush thoroughly with water for 15 minutes and seek medical attention. Skin contact: Wash off with soap and water. For emergency information call CHEMTREC at 800-424-9300.

Warranty

This product is designed to meet the performance specifications outlined in this product data sheet. If the product is used in conditions for which it was not intended, or applied in a manner contrary to the written recommendations contained in the product data sheet, the product may not reach such performance specifications. The foregoing is in lieu of any other warranties, representations or conditions, expressed or implied, including, but not limited to, implied warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade.

Easily fill cracks and voids in concrete or mortar joints! Use SAKRETE Concrete & Mortar Repair, a siliconized, acrylic-latex, repair product. Available in 300 mL tubes. Go with SAKRETE, The Pro’s Choice since 1936.

Product Code: 12021118

• High quality, repair product for flexible and durable crack-filling
• Ideal for filling cracks in walks, drives, foundations and mortar joints
• Fill vertical and horizontal surfaces
• Weather-resistant after curing and protects against freeze-thaw cycling
• Fills cracks with thicknesses between 1/8″ (3.2 mm) and 3/8″ (10 mm)
• Ready to use and fast-drying


SECTION 1: IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKING

1.1. Product identifier
Product name : Sakrete Concrete & Mortar Repair
Product code Not available

1.2. Relevant identified uses of the substance or mixture and uses advised against
Use of the substance/mixture : Sealant

1.3. Details of the supplier of the safety data sheet
Sakrete of North America
625 Griffith Rd., Ste 100
Charlotte, NC 28217
T 866-725-7383

1.4. Emergency telephone number
Emergency number CHEMTREC
1-800-424-9300 [USA] / +1 703-527-3887 [CAN]

SECTION 2: HAZARDS IDENTIFICATION

2.1. Classification of the substance or mixture
GHS-US classification
Specific target organ toxicity – Repeated exposure 1

2.2. Label elements
GHS-US labelling
Hazard pictograms (GHS-US) :
GHS08
Signal word (GHS-US) :
Danger
Hazard statements (GHS-US) :
Causes damage to organs through prolonged or repeated exposure.
Precautionary statements (GHS-US) :
Do not breathe dust/fume/gas/mist/vapors/spray. Wash hands thoroughly after handling. Do not eat, drink or smoke when using this product. Get medical advice/attention if you feel unwell. Dispose of contents and container in accordance with all local, regional, national and international regulations.

2.3. Other hazards
No additional information available.

2.4. Unknown acute toxicity (GHS US)
25 percent of the mixture consists of ingredients of unknown acute toxicity

SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS

3.1. Substance
Not applicable.

3.2. Mixture

Name Product Identifier % GHS-US Classification
Limestone (CAS No) 1317-65-3 45 – 65 Not classified.
Titanium dioxide (CAS No) 13463-67-7 0.05 – 5 Carc. 21
Stoddard solvent (CAS No) 8052-41-3 0.05 – 3 Flam. Liq. 3
Skin Irrit. 2
Asp.Tox.1
Ethylene glycol (CAS No) 107-21-1 <2 Acute Tox. 4 (Oral)
Eye Irrit. 2B
STOT RE 1
Quartz (CAS No) 14808-60-7 <0.1 – 1.0 Carc. 1A1
STOT RE 11

1Only applies to airborne particles of respirable size

SECTION 4: FIRST AID MEASURES

4.1. Description of first aid measures
First-aid measures after inhalation : If breathing is difficult, remove victim to fresh air and keep at rest in a position comfortable for breathing. Get medical advice/attention if you feel unwell.
First-aid measures after skin contact : If irritation occurs, flush skin with plenty of water. Get medical attention if irritation persists.
First-aid measures after eye contact : In case of contact, immediately flush eyes with plenty of water for at least 15 minutes. If easy to do, remove contact lenses, if worn. If irritation persists, get medical attention.
First-aid measures after ingestion : If swallowed, do NOT induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. Get medical advice/attention if you feel unwell.

4.2. Most important symptoms and effects, both acute and delayed
Symptoms/injuries after inhalation : May cause respiratory tract irritation.
Symptoms/injuries after skin contact : May cause skin irritation. Symptoms may include redness, drying, defatting and cracking of the skin.
Symptoms/injuries after eye contact : May cause eye irritation. Symptoms may include discomfort or pain, excess blinking and tear production, with possible redness and swelling.
Symptoms/injuries after ingestion : May be harmful if swallowed. May cause stomach distress, nausea or vomiting.

4.3. Indication of any immediate medical attention and special treatment needed
Symptoms may not appear immediately. In case of accident or if you feel unwell, seek medical advice immediately (show the label or SDS where possible).

SECTION 5: FIRE FIGHTING MEASURES

5.1. Extinguishing media
Suitable extinguishing media : Treat for surrounding material.
Unsuitable extinguishing media : None known.

5.2. Special hazards arising from the substance or mixture
Fire hazard : Products of combustion may include, and are not limited to: oxides of carbon.

5.3. Advice for firefighters
Protection during firefighting : Keep upwind of fire. Wear full fire fighting turn-out gear (full Bunker gear) and respiratory protection (SCBA).

SECTION 6: ACCIDENTAL RELEASE MEASURES

6.1. Personal precautions, protective equipment and emergency procedures
General measures : Use personal protection recommended in Section 8. Isolate the hazard area and deny entry to unnecessary and unprotected personnel.

6.2. Methods and material for containment and cleaning up
For containment : Contain and/or absorb spill with inert material (e.g. sand, vermiculite), then place in a suitable container. Do not flush to sewer or allow to enter waterways. Use appropriate Personal Protective Equipment (PPE).
Methods for cleaning up : Scoop up material and place in a disposal container. Provide ventilation.

6.3. Reference to other sections
See section 8 for further information on protective clothing and equipment and section 13 for advice on waste disposal.

SECTION 7: HANDLING AND STORAGE

7.1. Precautions for safe handling
Precautions for safe handling : Avoid contact with skin and eyes. Do not breathe dust/fume/gas/mist/vapors/spray. Do not swallow. Handle and open container with care. When using do not eat, drink or smoke.
Hygiene measures : Wash hands before eating, drinking, or smoking. Launder contaminated clothing before reuse.

7.2. Conditions for safe storage, including any incompatibilities
Storage conditions : Keep out of the reach of children. Keep container tightly closed. Store in a dry, cool area. Keep from freezing.

7.3. Specific end use(s)
Not available.

SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION

8.1. Control parameters

Limestone (1317-65-3)
ACGIH ACGIH TWA (mg/m3) 10 mg/m3
OSHA OSHA PEL (mg/m3) 15 mg/m3 (total dust)
5 mg/m3 (respirable fraction)
Titanium dioxide (13463-67-7)
ACGIH ACGIH TWA (mg/m3) 10 mg/m3
OSHA OSHA PEL (TWA) (mg/m3) 15 mg/m3 (total dust)
Stoddard solvent (8052-41-3)
ACGIH ACGIH TWA (ppm) 100 ppm
OSHA OSHA PEL (TWA) (mg/m3) 2900 mg/m3
OSHA OSHA PEL (TWA) (ppm) 500 ppm
Ethylene glycol (107-21-1)
ACGIH ACGIH Ceiling (mg/m3) 100 mg/m3 (aerosol only)
OSHA Not applicable
Quartz (14808-60-7)
ACGIH ACGIH TWA (mg/m3) 0.025 mg/m3 (respirable fraction)
OSHA OSHA PEL (TWA) (mg/m3) ((10 mg/m3)/(%SiO2+2) TWA (resp))
((30 mg/m3)/(%SiO2+2) TWA (total))
((250)/(%SiO2+5) mppcf TWA (resp))

8.2. Exposure controls
Appropriate engineering controls : Use ventilation adequate to keep exposures (airborne levels of dust, fume, vapor, etc.) below recommended exposure limits.
Hand protection : Wear suitable gloves.
Eye protection : Safety glasses with side shields.
Skin and body protection : Wear suitable protective clothing.
Respiratory protection : Not normally needed. In case of insufficient ventilation, wear suitable respiratory equipment.
Environmental exposure controls : Maintain levels below Community environmental protection thresholds.
Other information : Do not eat, smoke or drink where material is handled, processed or stored. Wash hands carefully before eating or smoking. Handle according to established industrial hygiene and safety practices.

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

9.1. Information on basic physical and chemical properties

Physical State

Liquid

Appearance Paste-like compound
Colour Black or grey
Odour

Sweet acrylic with slight ammonia odour

Odour Threshold No data available
pH

7.5 – 9

Melting Point No data available
Freezing Point < 0 °C (< 32 °F)
Boiling Point

> 200 °F (> 93.3 °C)

Flash Point

No data available

Relative evaporation rate (butylacetate = 1) No data available
Relative evaporation rate (ether = 1) > 1
Flammability (solid, gas)

Not flammable

Explosive limits No data available
Oxidising properties No data available
Vapour pressure 25 mm Hg @ 68 °F (20 °C)
Relative density No data available
Relative vapour density (air = 1) > 1
Solubility Dispersible
Partition coefficient: n-octanol/water No data available
Log Kow No data available
Auto-ignition temperature No data available
Decomposition temperature No data available
Viscosity No data available
Viscosity, kinematic No data available
Viscosity, dynamic No data available

SECTION 10: STABILITY AND REACTIVITY

10.1. Reactivity
No dangerous reaction known under conditions of normal use.

10.2. Chemical stability
Stable under normal storage conditions.

10.3. Possibility of hazardous reactions
No dangerous reaction known under conditions of normal use.

10.4. Conditions to avoid
Heat. Incompatible materials.

10.5. Incompatible materials
Strong oxidizers.

10.6. Hazardous decomposition products
May include, and are not limited to: oxides of carbon.

SECTION 11: TOXICOLOGICAL INFORMATION

11.1. Information on toxicological effects
Acute toxicity : Not classified.

Sakrete Concrete & Mortar Repair
LD50 oral rat > 2000 mg/kg
LD50 dermal rabbit > 2000 mg/kg
LC50 inhalation rat No data available
Limestone (1317-65-3)
LD50 oral rat 6450 mg/kg
Titanium dioxide (13463-67-7))
LD50 oral rat > 10000 mg/kg
Ethylene glycol (107-21-1)
LD50 oral rat 4000 mg/kg
LD50 dermal rabbit 9530 μL/kg

Skin corrosion/irritation : Based on available data, the classification criteria are not met.
Serious eye damage/irritation : Based on available data, the classification criteria are not met.
Respiratory or skin sensitisation : Based on available data, the classification criteria are not met.
Germ cell mutagenicity : Based on available data, the classification criteria are not met.
Carcinogenicity : Based on available data, the classification criteria are not met.

Titanium dioxide (13463-67-7))
IARC group 2B – Possibly carcinogenic to humans (airborne, unbound particles of respirable size)
Quartz (14808-60-7)
IARC group 1 – Carcinogenic to humans (airborne, unbound particles of respirable size)
Quartz (14808-60-7)
National Toxicology Program (NTP) Status 2 – Known Human Carcinogens (airborne, unbound particles of respirable size)

Reproductive toxicity : Based on available data, the classification criteria are not met.
Specific target organ toxicity (single exposure) : Based on available data, the classification criteria are not met.
Specific target organ toxicity (repeated exposure) : Causes damage to organs through prolonged or repeated exposure.
Aspiration hazard : Based on available data, the classification criteria are not met.
Symptoms/injuries after inhalation : May cause respiratory tract irritation.
Symptoms/injuries after skin contact : May cause skin irritation. Symptoms may include redness, drying, defatting and cracking of the skin.
Symptoms/injuries after eye contact : May cause eye irritation. Symptoms may include discomfort or pain, excess blinking and tear production, with possible redness and swelling.
Symptoms/injuries after ingestion : May be harmful if swallowed. May cause stomach distress, nausea or vomiting.

SECTION 12: ECOLOGICAL INFORMATION

12.1. Toxicity
Ecology – general : May cause long-term adverse effects in the aquatic environment.

12.2. Persistence and degradability

Sakrete Concrete & Mortar Repair
Persistence and degradability Not established.

12.3. Bioaccumulative potential

Sakrete Concrete & Mortar Repair
Bioaccumulative potential Not established.

12.4. Mobility in soil
No additional information available.

12.5. Other adverse effects
Effect on the global warming : No known ecological damage caused by this product.

SECTION 13: DISPOSAL CONSIDERATIONS

13.1. Waste treatment methods
Waste disposal recommendations : This material must be disposed of in accordance with all local, state, provincial, and federal regulations. The generation of waste should be avoided or minimized wherever possible.

SECTION 14: TRANSPORT INFORMATION

14.1. Department of Transportation (DOT)
In accordance with DOT.
Not regulated for transport.

14.2. Additional information
Other information : No supplementary information available.
Special transport precautions : Do not handle until all safety precautions have been read and understood.

SECTION 15: REGULATORY INFORMATION

15.1. US Federal regulations
All components of this product are listed, or excluded from listing, on the United States Environmental Protection Agency Toxic Substances Control Act (TSCA) inventory.

Ethylene glycol (107-21-1)
Listed on United States SARA Section 313
EPA TSCA Regulatory Flag Y2 – Y2 – indicates an exempt polymer that is a polyester and is made only from reactants included in a specified list of low concern reactants that comprises one of the eligibility criteria for the exemption rule.
SARA Section 313 – Emission Reporting 1.0 %

 

15.2. US State regulations

Sakrete Concrete & Mortar Repair
State or local regulations This product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

SECTION 16: OTHER INFORMATION

Date of issue : 04/08/2015
Other information : None.

Disclaimer

We believe the statements, technical information and recommendations contained herein are reliable, but they are given without warranty or guarantee of any kind. The information contained in this document applies to this specific material as supplied. It may not be valid for this material if it is used in combination with any other materials. It is the user’s responsibility to satisfy oneself as to the suitability and completeness of this information for the user’s own particular use.


Product Calculator


How Much Do I Need?

Calculate how much of a product you need, then add it to your Shopping List.
Jump To Calculator Icon

Jump To Calculator

More Information

SAKRETE Concrete & Mortar Repair can be used to repair cracks in vertical and horizontal surfaces. To learn more, reference the Features & Benefits section of the Technical Data Sheet.